I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Please answer some questions below.
“Application” and “SoftDevice” can be replaced by DFU, correct?
Is Nordic DFU function inside “Module” (Orange colour part)?
If...
Hi
I am working on a product where I need a battery optimized beacon receiver - the opposite of what yo normal see with a beacon device where it is the transmitter which...
Hello,
I am currently using the sdk multiperipheral example. I use a nrf522832 as a central device and two nrf522832 as peripherals. I am connected to the two devices at...
I'm trying to make i2s working on mbed os by using NRF52 development kit board (based on nrf52832).
Looks like I'm missing something. What I managed to do so far is:
...
Hi,nrf52832 entered in bootloader mode.as ld5 led is keep blinking on power reset and holding if boot/reset button.please help me to get board back to normal mode.thanks.
HI,
I am working on NRF52832 SOC. with SDK 15. where i need to read the SENSOR data from twi protocol.
Common Write and Read Register function has been created
I...
Hi,
I would like to use the Raspberry Pi and the Thingy:52 as published in the demo. My question is, how many Thingy:52 devices are supported by the demo?
I have a nrf9160dk I followed the steps in the movie www.nordicsemi.com/.../GetStarted I have inserted my own sim that is working in my phone but I do not get LED3 and LED4...
Hi There
Is there any additional drivers that i have to install to use nRF connect on my Mac?
I've installed it and when i connect the nRF9160 DK to the Mac, it doesn...
Hi, I am trying to implement app_timer library with FreeRTOS. Based on my testings, it seems that app_timer_start() under app_timer_freertos.c has the lowest time resolution...
Good day
I moved from Mesh3.00 to mesh 3.1 and I see the way UUID is extracted is slightly different.
I would like to know when I copy the UUID to use in my project will...
Sorry for disturbing!
I have some questions about measuring nRF52832 32Mhz Crystal frequency.
I use an active probe(Tektronix P6243) to catch the signal and the test result...
In the case where connecting to a phone that is paired with my device after my device has cleared pairing information and doesn't remember the pair, I'm observing the following...
I'm working on a project to get two devices to agree on a secret key based off of physical layer properties.
My solution is for devices A and B to make 64 RSSI measurements...
