I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello.
I wrote a simple beacon application which advertises with uuid, major, minor and name. Now what I saw in sample beacon I found somewhere is that nrf connect properly...
Hello!I am using NRF52832. The antenna is aca-5036-a2-cc-s produced by INPAQ, but the bluetooth cannot be found.Whether the adaptive antenna can be provided and the technical...
Hi Every one,
I am trying to use two uart's communications concurrently in nrf51422, in my code i am running timer of one second.
Every one second in timer routine trying...
hi....
i am using nrf52382 and segger 15.2 version , i want my peripheral to send the data only if it reaches the certain limit (threshold value) on that case it should...
hello , friends
i am using nrf52832 ,debugged the ble uart program ,and then i tried to connect my device over ble uart app,i couldn't found my device ,then i tried to connect...
Good morning!
First of all, the background. I made a custom board and programmed it, everything worked like a charm. After that, I made another one, same hardware, same...
In my previous question , where I wanted to atomically send a large bulk of data, the solution was to keep track of p_bus-> free_buffers , in order to calculate the amount...
Hi,
I’m using SDK 15.00 and I have some issues with NFC. When I’m trying to connect with NFC - NFC_T2T_EVENT_FIELD_ON event occurs. At this point, I need to start BLE...
The release notes for S132 v6.1.1 lists a bug fix:
"Fixed an issue where NRF_TIMER0 may not be reset at the start of a radio timeslot (DRGN-10650)."
Did this bug exist...
Hi,
Here and here are examples of a port of the nice u8glib library to stm32. Based on these, i tried a port to nrf52, but was not successful so far.
I call the oled...
I am trying to save data to the flash memory. My starting file is the ble_app_uart_pca10040 (s132). I am using the sd_flash_write address is 0x007ffd0 and a value of 0; I...
We have developed a custom board using Raytac MDBT50Q with NRF52840. It has an external EEPROM and a RTC. We made an app that we use to program 4 daily alarms through BLE...
nRF51822-EK page is no longer available on the website. By any change I can get the PCA10001 schematic somewhere?
I would like to run some conductive RF testing and would...
