before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi,
When I define my nrf52840 pin 0.19 as input put, and there is no connection to any sensor.
Then I use gpio_pin_get_dt() to get pin 0.19 status, the status is high...
I downloaded the nRF Connect SDK v2.7.0 and read the Release Notes. I installed the v2024.7.18 (pre-release) version of the nRF Connect for VS Code. As a first step, I created...
Greetings
I am trying to configure the nrf5340dk to use the i2c0 bus. I believe i2c1 is already configured, but for learning purposes, I want to figure out how to do this...
Hi,
When I DFU upgraded the bootloader of my firmware, I found that during the upgrade process, when ret_val = bl_activate() was executed, the pin would be pulled low. ...
The product page for the Thingy53 only shows hardware files for the v0.8.0 board revision, not the 1.0.0 or v1.1.0 board revisions.
https://www.nordicsemi.com/Products/Development...
HI all!
So I'm trying to use and modify parts of the Asset Tracker v2 application for my own project and when I created a new application with the pre-existing sample on...
Hello all,
I am trying to write some code to read the sensor values from two VL53L0X tof sensors, but I'm having some trouble.
My current code:
My devicetree:
...
I am using the cloud client example and connect to the nRF Cloud. I receive message fine on an interval and when I press the button.
I do not get any notification in my...
Hi all,
I am hoping to eventually integrate the crashlog functionality, but prior to this, I wanted to test the basic functionality with the flashlog. I have looked through...
Hi,
I'm currently working on getting LTE to work on our custom card, featuring an nRF9161 and an MFF2 eSIM (without PIN), but I can't seem to initialize our eSIM. I have...
Hi,
I know this issue has been addressed in other posts but none of the solutions tested worked for me. I tried the solution of this post : Intellisense stops working when...
hw: nRF9160-DK, v1.1.0
Using the McuBoot-Loader of NCS 2.5.1 and the NCS 2.6.1 zephyr dfu module seems to be not longer aligned with it.
A app using NCS 2.5.1 zephyr's...
We are developing Matter/Thread based Smart Lock product. One of the product requirements is that the product should be able to connect to a BLE mobile APP at all times i...
Hi,
The CPU temperature module is located in the network CPU in the case of nRF5340. I have read this thread : Zephyr API to read the nRF5340 die temperature - Nordic Q&A...
