Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Dear Nordic team, We are using the nRF connect SDK version 2.1.2. Our prototype uses the nrf52840dk board and the KScan application template. However, when directly trying...
Hi,
Want to update the linker script as below in segger embedded studio? How to add this using flash_placement.xml. //update your linker script (.ld file) to expose information...
I'm trying to use the ADC on the DK52 (PCA100040) to sample and transmit data to a PC. I've been able to write code that samples data to a buffer and I've modified the peripehral...
Dear all,
I've got some problems with the uart implementation in the peripheral uart example. I am using nRF52833 DK and SDK 2.0.2.
What I need for evaluation is a device...
I've the following situation:
1. Send CoAP message trough send(), this causes the the nRF9160 to start RCC connection
2. Wait for RCC connected mode (LTE_LC_RRC_MODE_CONNECTED...
Hello!
I am in the process of adding OTA DFU support to our existing application. However, I'm having problems starting the DFU process.
For security reasons we want to...
Hi there,
We are using the nrf9160 DK with Serial LTE Modem (1.8.0) to run some tests on the modem (1.3.1). We are using the MQTT client AT commands in order to connect...
Good day
I am attempting to use lwm2m to post temperature sensor data. At the moment I'm trying to to initialize object with ID 3300 (generic sensor)but it is not appearing...
MacOSX 13.0.1, Intel. nRF Connect SDK v2.2.0 as downloaded by Toolchain Manager v1.2.1 from nRF Connect for Desktop 3.12.1.
Same happened with SDK v2.1.2.
Similar steps...
Hi,
I was trying to put the nRF5340 Audio DK board in DTM mode to test RF capability but couldn't find out any way to do so.
Please let me know if I can find some documentation...
Hi,
We have 3 nrf5340 Audio DKs we want to connect together. One of the devices is connected as central and the two others are connected as peripheal. By know, the two peripheal...
Hi!
We plan to build an AoA localization system with the nRF52833. To calculate the signal phases per channel, the antennas are connected to the BLE-RX via switches sequentially...
I am working on the nfc uart examples. first I found the poller example is not support for 10056 board. I make the change for that. code can build and flashed, but then I...
Hello,
My development requires new device binding and I want to share the steps followed and my issue.
My device is Renesas and commuicate via I2C protocol.
Based on...
