before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi,
During the validation of our device, we found that the RTC (synthesized from HFCLK) was quite a bit off. Instead of the expected 32.768kHz, we measured 33.047kHz.
...
Hi, I am using urf52832 ( also have 52833 dk).
I am trying to use another pin us uart, which tx is 29 rx is 30 define in project_pinconfig.h.
But I can't see any uart...
Hello, I'm working with BLE Mesh using NRF52840
- Our setup: NRF-Connect-SDK 2.1.0
- Summary of our project.
+ Provisioner node to control lightness for all nodes in...
Hi,
I'm having an issue including USB DFU Trigger library in my prototype application running on nRF52833.
My application is based on the ble_uart example, to which I...
Hi,
My application is written on top of freertos ble example. I need to integrate radio test example as well for certification. I am running into errors when I try to...
Hello,
my first Post here, so i hope i do it correctly.
I have the following Problem with the Configuration and Communication over TWI/I2C.
The Voltage of the TWI...
I am working on BLE on NRF52840 using soft devices for BLE and I was using sd_ble_gap_ppcp_set API to set the connections parameters for the BLE so I think the PPCP is the...
I'm calling this function from a Zepyhr project:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/connectivity/bluetooth/api/gap.html#group__bt__gap_1gad2e3caef88d52d720e8e4d21df767b02...
Hi, I am trying to test multi_sensor example from Zigbee and Thread SDK 4.2 using official Nordic nrf52840DK with few Zigbee hubs. Example is located in \examples\zigbee\experimental...
Hi
My thingy91 does not appear in the Connected Devices list in VS Code. I've tried everything now.
What's the prerequisites for getting this to work?
Do I have to install...
I'm using a nRF5340DK with nRF Connect SDK v1.9.0 and want to use MCUBoot with Direct-XIP.
Using the hello_world sample project, I added MCUBoot.
In the MCUBoot prf.conf...
I have issues with my NRF5340DK devices that I'm hoping to get support on. Several devices appear to be bricked, stuck in a boot loop or otherwise unable to program using...
Hi, I'm hoping someone could advise on interfacing with the T2 LC3 codec included in nRF Connect.
The context is I have stereo I2S microphones providing 24-bit 2's complement...
