before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
If I would like to add Bluetooth capability to the nrf9160, can the nrf5340 be used as a "companion" MCU?
Would be great if there is a pre-build firmware for the nrf5340...
Hi,
I am trying to write a program that connects my phone to my nRF52840-DK board; I then send one of two commands from my phone, then the nRF52 will respond accordingly...
Hello,
Recently, in my organization we have decided to transition from nRF5 to nRF Connect SDK and while going through this process we noticed an issue with the source control...
Hello, I am trying to get the peripheral_lbs example to unpair all devices (delete all bond informations) using VSCode and nrf connect sdk version 2.0.2.
I tried using bt_unpair...
As part of the NCS install, in the ncs\vx.y.z\Zephyr\doc folder there is a ton of Zephyr documentation (more then 13MB) in .rst format. How do I use this instead of the online...
Hi all
I've tried to build the nRF5340: Multicore application on different host platforms using the nRF Connect SDK v2.1.0. It worked without any problems on Windows and...
Hi,
I'm using NRF52832 with s132 softdevice for a low power project. I notice that when running firmware with DFU Buttonless, the SoC consume more power than without it...
Hi,
I'm trying to reproduce the fatfs example on a nrf52840 DK and Sandisk micro SD card that's plugged into a Sparkfun Transflash breakout board. I can't seem to mount...
Hi everybody,
I'm working on a project where I want to write in an external flash nor memory, and transfer data over BLE. The combination of the peripherical_uart sample...
Hello,
I need to sample 2 saadc channels at 6Khz, and another saadc channel at approx 1/sec for a battery measurement. Which are configured for channels 0,1 and 6 respectively...
Hello all I am using nRF52832 I am using SEGGER Embedded studio for programing. I want to use pins 12 and 11 as Rx and Tx for UART. I changed the default pins to #define RX_PIN_NUMBER...
Hi,
Two weeks ago, I've tested my new devices in an anechoic chamber. I'm using Fanstel BT840X modules. These modules are using nrf52840 for MCU/Radio and SKYWORKS SKY66112...
Dear Nordic Support
I scanned through the DevZone Topics, and found a few tickets concerning MQTT-SN support.
As far as I have seen, MQTT-SN was once supported in the...
How can I enable a matter accessory device to actively send data to a matter control?
I'm using matter-lock sample to test the method of sending data from the matter-accessory...
