I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
nrf52833 custom board
My query is that how to do OTA DFU on ble central devices (we are using nrf52833 as receiver dongle(ble central) device)? Does anyone advice...
Hi all,
when I follow the blog as below, find the actual output is not same as expected.
Adding a Peripheral to an NCS Zephyr project - Peripherals And RF Test - nRF Connect...
Hi Everyone,
I recently purchased the NRF52840 DK with a PCA10056 designation. I connected the DK to my Windows 7 laptop via the USB. This resulted in the JLINK(D:) drive...
I have a custom board with a nRF52805 module but I don't understand how the SDK works.
I followed some guide to simulate nRF52805 software, I had to patch some files in...
Hello,
I add sd_ble_gap_phy_update() in the ble_evt_handler() as below:
case BLE_GAP_EVT_CONNECTED: { ...... ble_gap_phys_t const phys = { .rx_phys = BLE_GAP_PHY_2MBPS...
The CONFIG_CLOCK_CONTROL_NRF_K32SRC_EXT_FULL_SWING=y Kconfig option causes kernel booting to hang at line 505 of clock_control_nrf.c.
This is on the v1.7-branch of NCS ...
I have created a custom board containing the nRF52832. I have two copies. The first board works, meaning that I have flashed the code to it using the DK52, and I can power...
Hello,
I have been evaluating the nrf9160 DK board. And my application is using mbedtls (vanilla) and TFM (Used https_client as a starter project). The problem is that with...
Hi,
I'm new to nRF/Zephyr development and trying to integrate the OV7670 camera with the nRF52840 board. Since there was no driver for this particular camera I ported the...
I'm having a problem with what should be a very simple exercise. I'm trying to compile the Zephyr sample subsys/cpp/cpp_synchronization after adding #include <string> to the...
Hello,
I am trying to read data from LS2DE12 accelerometer MEMS chip via I2C bus and I am seeing only zeros for all 3 axes.
I can write to the various registers successfully...
Hello, I ran the nrfconnect (ver 3.7.1) in Power Profiler (ver 3.1.3) in BLE advertising.
When I run the source mode on 3000V I get normal peaks (20mA), however when I run...
Hi,
I'm interested to use AGPS in my project. Looking into AGPS example (link below) , I want to prevent using low power mode since as far as I know using this command you...
