I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi,
I'm running example mqttsn_sleepy_subscriber from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 on a nRF52840-DK with RaspPi_OT_Border_Router_Demo_v4.1.0-1.alpha.img...
Hello Nordic Team,
I am trying to flash the existing BLE light example code in nRF connect sdk to my BL653 kit with Segger Embedded Studio. The node is not getting detected...
Hi.
I'm facing an issue following this guide ( https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/software/posts/using-a-custom-secure-partition-manager-wtih...
I am using running "ble_app_uart_c" example in my Central nrf52 DK board and ruuning "ble_app_uart" example in my peripheral nrf52 dk board..
IF I am sending ASCII values...
Hi,
I'm working on a multilink central device with SDK16, nRF52832.
I'm trying to connect the central to 2 peripherals with certain address. So I added 2 address filters...
Hi all,
I have a nRf52832 Buttonless DFU setup and application is BLE APP UART.
nRF52 SDK = 17.0.2
I need to send a hex file of STM32F4 through UART. Do you have any...
Hello
I'm using sdk17.0.2. And I'm using the ble_nus service with the addition of nrf_crypto (AES_CTR).
I originally used nrf52832 and pca10040 and the test went well...
I just got a new nrf9160DK rev 0.15.0. While plugged in to USB and the switch in the off position, my meter reports 4.95V and 0.016A. Why is this happening? My older rev 0...
From the product spec, the voltage accuracy is listed as -10, +5% from the programmed value. We're using 3.0 V. For our application I need some more specifics on this regulator...
Hi,
I'm building DFU secure_bootloader with oberon crypto library as mentioned here https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts...
Hi,
I'm developing an Android app using the nRF Mesh Library. I have a scenario in which a few phones need to be provisioners given that these will configure new nodes...
prj.conf of light demo:
Can you tell me where CONFIG_LOG is enabled? It is inconsistent with ncs1.5.0. When I enabled CONFIG_LOG_BACKEND_RTT, I was notified of an...
I am trying to program a PCA10059 USB dongle which requires it to go into DFU mode.
I have tried pressing the white button when it is plugged in, and I have tried holding...
I can't seem to find the answer here - sorry if it has already been answered. We were having an issue recently where the root cause ended up being that we were trying to do...
