Hi,
I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
I’m using nrfjprog version 10.12.1 and JLinkARM.dll version 6.88 . I encountered an intermittent nrfjprog error when programming firmware to the nRF52833 .
In most cases...
Hi,
I am trying to use mcuboot to load a version that is stored in my external flash, and I cannot get it to boot. My project is being built using sysbuild and my target...
hi i have a question
i ues ncs 2.9.0
This is the code that displays my Bluetooth connection
——————————————————————————————————————————————————
struct bt_data ad[]...
I am trying to run the debugger from the nrfconnect extention for viual studio code. for some reason It doesnt work, It seems to flash the app fine, but then this message...
Hello Team,
I’m working on creating a custom Matter cluster using the instructions provided in the Nordic documentation: https://docs.nordicsemi.com/bundle/ncs-latest/page...
I'm getting the following warning on my terminal during build:
-- Including generated dts.cmake file: D:/Workspaces/azure_iot_hub_9/build_pmi/mcuboot/zephyr/dts.cmake CMake...
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
Hello DevZone,
I have learned that some knowledge about CLOCK. But they are a little bit confusing. I just want to get confirmed by any expert.
1. Some peripherals ...
Hello,
I am looking to create my own custom NRF5340 AUDIO DK board. Could you point me to any NRF5340 modules that would be best to use with a pre-built antenna, available...
NRF52840DK NCS 2.8.0 Hello , We are developing an application where a device with router function must join a coordinator network. The coordinator uses OOB (proprietary IR...
I am working with the WLCSP version part (nRF54L15-CAAA) and it calls out that there is light sensitivity. The note seems to indicate that only underfill around the perimeter...
how to upload modem firmware and and connect to nrf cloud and send modem firmware and asset tracker hex file and procedure to connect to nrf cloud ( i tried and sim activated...
Hello, I searched the forum for similar issues and found a few, such as
I am currently implementing a PSRAM is66wvs4m8 on the Thingy 91 via SPI, using SPIM3.
The problem...
I get the source code from the github.com/.../ncs-fund.git , and trying to build the exercise-1-5 of nrf-connect-sdk-fundamenta lesson-4-serial-communication-uart for 54l15dk...
