Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello,
I am trying to resolve some compliance issues with the third-party libraries that are used in the SDK. For nanopb, it seems like the changes in pb_decode.h mentioned...
Hello,
I want to configure pin 0.13 as a rising edge interrupt.
Is there any sample code to configure the pin and interrupt handler?
Thanks in advance.
Hello,
In a previous post I asked about scanning and connecting based on specific advertised data. After some testing I realized that my two nrf dks only connect sometimes...
Hello; We want to use the GPS peripheral of nRF9160. Qorvo QM14501SR LNA is used in your evaluation board. QM14501SR is expensive for our project. Can we use LNA without band...
Hi,
i am working on nrf52832 . i am facing advertising issue with custom board. controller advertise only when i touch 32.786kHz crystals or two capacitors with my finger...
Hi,
I use example projects Thread: CoAP Client and Thread: CoAP Server . I can send and receive data over CoAP. My purpose is to use CoAP, CoAPS and UDP tohether. If client...
nrf_ringbuf has a bug which happens when mixing nrf_ringbuf_cpy_put() with nrf_ringbuf_alloc() and nrf_ringbuf_put(). After copying data with nrf_ringbuf_cpy_put() a later...
Hello,
at the moment we are trying to realize a low power delay with the usage of the APP_TIMER.
We need a low power delay over 10 seconds.
This is our attempt:
...
Hello,
we are developing an application with a nRF52832 on a custom board. The application works fine. The application on the nRF52832 consumes 2.2mA @ 2.5V.
The other...
Hello,
Our Project
at the moment we are developing an application with a BMD-350, which contains a nRF52832 chip.
The BMD-350 is on a custom PCB with another microcontroller...
Hi,
I am trying to prgram the nRF52840 DK board (revision 2.0.1) within a virual machine (VirtualBox running Linux Mint). I have installed the SDK and the nrf command line...
I'm not even exactly sure how to describe this problem, so please bear with me. I have a setup with two nRF52840s, one of them (call it B) functions as a peripheral server...
I have two devices, both nRF52840, one as Client, one as Server. There are a few services defined with a few characteristics in each. Two of the services have values like...
