I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi. I was wandering if there is a difference if I put the TASKS_CALIBRATEOFFSET before TASKS_START , and vise versa. However, I saw in this link: infocenter.nordicsemi.com...
Hi,
According to the documentation the maximum admissible current for the DUT in ampere mode is 1A. What happens if the current goes higher than this ? I suppose that it...
Hi,
I would like to store 180 000 bytes on the flash with fstorage. By using the example after some trouble it works. When I try to apply this example on my own program...
I've seen several questions on this forum on issues with setting up the NRF LOG, however, I am still having many issues and I can't seem to get UART logging working.
I am...
Trying to test the 1ms sample on the NRF5340DK. Loaded and ran the app without problem.. it starts with 9XXXXus. Runs with couple of drops. But when 1ms interval is started...
Hi there,
I have the following settings:
- nrf52810 on a custom board
- only the mandatory GAP service and one custom service with three characteristics, everything...
Hi all,
I have the following issue: For an electrochemical measurement I need to use 4 GPIO pins bundled in pairs, each pair with an output (GPIO HI) and ground (GPIO LO...
I'm evaluating nRF9160 + Serial LTE Modem application for a battery powered device that uploads data via HTTP POST 8-12 times per day. Since all interactions are initiated...
Normally when we send data via UDP we get a +CEREG: 5 response.
We use this to generate a signal <e_ready which in turn allows the next message to be sent.
(As per the...
Hi
I wants to do POC on LE audio, I know nrf5340 support all Bluetooth5.2 spec. Where can I found LC3 codec that can help me for POC? is Zephyr LC3 codec can help?
https...
I'm doing a bit of research on Nordic Semiconductor devices and am currently looking into devices that use a nRF52x chipset.
I have been looking around the internet for...
Hello , I am working on a project which contains I2C communication, When I test the twi scanner example on my sensor and it works fine But when I do the combination with the...
I'm trying to update our LTE connection library to use the LwM2M Carrier library to be prepared for carrier certification and I am not seeing any way to request that the modem...
1.Project only has one main.c file. Other files are in zephery public folders,like conn.c etc.
My problem is ,if I modified conn.c for one project, how about the other project...
Hi, I've recently been diving into the whole trustzone implementation on Zephyr and I'm having trouble understanding how to properly work with it.
My question is fairly...
