I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hello everyone.
I have a nRF52840 DK that I am working with.
1.) When I plug into the USB port J2 (MCU interface) I am able to connect to the board program/debug using...
I wrote some code that has multiple custom services where my device acts as GATT Server.
I register the handler for every service (3 in total) with NRF_SDH_BLE_OBSERVER...
Hi,
I am debgging QSPI( type name: IS25LQ040B) in nRF52833, I met " NRFX_ERROR_TIMEOUT ", Could you give me some advice, please?
// Set QSPI pins to pins related to...
Using this \nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_blinky and nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_blinky_c
As described in \examples\ble_central...
Dear community,
I'm facing a problem during bluetooth scanning. I'm using the example named in the subject. This allows me to use the UART as debug printout.
I slightly...
Hi, I'm trying to upgrade nRF Connect SDK from 1.3.0-rc1 to 1.3.0 because I need one of the bugfixes to keep developing. I'm on macOS catalina and I've used the Toolchain...
Hi,
I am looking at and testing the ble_app_hrs_c_pca10040_s132 example.
When the whitelist ist set up with the "whitelist request" we execute the following two lines...
Hi,
I am developing an application that requires communication between two nrf52840-based devices. There is a scenario in my application where the devices needs to exchange...
Hi,
[179] RTC: COMPARE event is generated twice from a single RTC compare match
This anomaly applies to IC Rev. Revision 2, build codes CKAA-Dx0, QIAA-Dx0.
It was...
Hi everyone, I'm an intermediate level nRF Connect SDK IDE programmer, and I describe my issue below:
1.- In the link below I found an example of code for the analog port...
The SDK version is using version 17 and I am using NRF52832.
I checked the following scope waveform for the next SPI communication.
Question
I want to remove the...
nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10056_ble\arm5_no_packs
Why the compiled hex file is different from before, and the code is not modified
I like to use nRF toolbox to monitor my glucose meter. To my understanding, after the glucose device connected with nRF toolbox, they will be exchanging data. So my question...
Hi,
When attaching external GPS Antenna to Nordic Thingy91, I realize that the power consumption increases by about 5mV. Are there any ways that I can config to unuse this...
