I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello Everyone,
We are using nRF52840 IC for our products which has 1 MB of flash.
Thread Secure DFU Example provided with Nordic SDK supports only Dual Bank DFU. This...
Hi,
I'm working in the asset tracker v2 project and currently I need to do a simple hex to char array conversion. This entails using sscanf. However the use of sscanf consistently...
Hi, I am trying to expand on the ESB PRX example and want to recreate functions with the same functionality as Arduino's micros() and millis() functions. I'd like the following...
Hello, Nordic & all:
I have a problem when use P0.21 as the libuarte's uart RX( base on libuarte example/sdk17.0.2) for my custom nrf52840 board， I looked up the reference...
We just received a PPK2 and have used it in several configurations to test a custom nrf52832 board that runs on a 3v lithium coin cell.
When connected in the following manner...
Hello:
I am working on an application that uses a simple UDP socket for transmitting data. I would like understand the zephyr BSD socket behavior when there are cellular...
Hello,
I see a number of threads on the Nordic devzone where people are asking about official support for a DFU bootloader that combines BLE and UART for transports. Most...
hello Nordic
i am working with nrf52840, SDK16.0, s140 (maybe i will change softdevice later)
i build a project on the peripheral blinky example, i change the advertising...
Hello,
My application is based on the example "ble_thread_dyn_mtd_coap_cli" (nRF5_SDK_for_Thread_and_Zigbee_v4.1.0). I would like to be able to send large files via Bluetooth...
Setup -
nRF52840-DK
Nordic Connect SDK version 1.5.0
Sample - nrf/samples/peripheral/lpuart
Commented out "uart0" in the board specific overlay
Uncommented console...
Hello i'm trying to compilate the project secure_bootloader_ble_s132 but i'm having issue with micro-ecc.
when i complie on keil the bootloader exemple i get this error...
Hello,
As the question shows, how to add RTC function to a 5340 empty project?
condition
ncs:1.5.0
board: nrf5340dk
I have found a project,but it's 52840.
...
Hello,
My application runs in non-secure mode on the nRF9160, and I would like to disable external access to CPU, RAM and Flash.
I understand this is done by setting the...
Hello
I have board nRF52833 and i have several questions:
1. Is AoA example available ? I would prefer to have example of software for tag and for the localization...
On a custom board based on nrf52840.
We want to implement OTA DFU with radio (not necessarily BLE, e.g Serial 4G Modem)
We already checked the Serial DFU example and made...
