I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi Dear
Good Day!!
I want to know about which clock frequency they are used in nrf5SDK internal or external FREQ, and along with the where can i find the declarations...
Hello,
I am trying to work on an application to transfer BLE characteristic data to an SD card.
I ran the FATFS example on my setup and it works perfectly with the Test...
Dear sir.
I'm an engineering working on circuit design , micom program, and PCB artwork. from korea. My name is Jeong eui-jong.([email protected])
In conclusion,...
Dear Nordic Team,
I am currently using nRF52840 with nRF5 SDK v16.0.0 for developing a prototype of wearable device.
The wearable device should be able to act as
a)...
I'm implementing the full modem firmware update as demonstrated by the sample located at /samples/nrf9160/http_update/full_modem_update.
A bunch of it works. I'm able to...
I try to modify one of the pc-ble-driver examples to work together with my PCA10040 and the Nordic UART Service example in my Qt application, but the application doesn´t discover...
Hello,
I'm currently using SDK v17.0.2 with the NRF52840 on nRF52840-DK Board. After going through the example code of "nrfx_spim" I was able to get up and running. I...
Hi, I am trying to integrate DWS3000 (UWB) APIs, given here to nRF52840 with BLE stack enabled such that my firmware can blink Eddystone packets at the same time when UWB...
The customer requested that pairing be prohibited under certain circumstances, so I called API
sd_ble_gap_sec_params_reply(m_conn_handle, BLE_GAP_SEC_STATUS_PAIRING_NOT_SUPP...
in ~/ncs/zephyr/samples/hello_world/prj.conf or in ~/ncs/zephyr/boards/arm/nrf9160dk_nrf9160/nrf9160dk_nrf9160ns_defconfig
CONFIG_I2C=y
in my nrf9160dk_nrf9160ns.overlay...
Hi,
We are using nrf52833 for measuring angle of arrival. We got IQ samples from the device we need to calculate the phase difference from that IQ sample. please explain...
Hi, we have an application using an nRF52832 without a SD that we want to put into low power / sleep mode to save battery.
What commands should we use to do this and wake...
Hi,
I am using ppi to read some continuous data from a sensor through SPI and i got it working, it reads data in evry 8ms from the sensor through ppi.
but it fails when...
