I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I want to use nrf52840 dongle as a provisioner to provision other server and client nodes. So, i was trying to program dongle by using seggger and building and running...
Hi,
I am currently trying to create a bootloader for a project I am working on. I am familiarizing myself with the dfu and bootloader modules by running one of the example...
Currently I have implemented Central using nrf52810, SDK 14.2 / Softdevice S132.
I want to know how to do OTA upgrade in Central.
Or I would like to get an example currently...
What's the proper way to turn off BLE to conserve power?
I have a board with DC power input and battery backup. When the DC power fails, I want to finish what I'm doing...
I have an nRF 52832 running the SDK 15.2. I have a few general questions because I'm seeing behavior I don't understand and doesn't seem to be right.
If I erase all the...
I am attempting to load up the default NRF project "AT_Client" located at ...\ncs\v1.4.2\nrf\samples\nrf9160\at_client project, however, whenever I attempt to load it with...
Hello
I studying the nrf9160 , is it better to use the UART interface versus the SPI and do I need to use the flow control ?
Thanks a lot
Stephane Boudaud
Hi,
We developped a custom NRF9160 board and it works fine, it connects to LTE-M. We then designed a new version of the same board by adding few things (like NRF52833 MCU...
The sample code at ncs/nrf/samples/nrf9160/mqtt_simple is not connecting. I dod not make any changes to the ode. I am using NB-IoT. LTE is connected. The link monitor, LTE...
I just spent hours trying to use TTM with nRF52840 and I wanted to share the fix:
You need to use the Thread FTD CLI (USB) pre-compiled binary from v4.0.0 of nRF SDK for...
I would like to clarify my understanding of the connection interval since it doesn't seem to match what I'm seeing in the nrf connect mobile app.
Currently I've set my...
Hello all!
I have been modifying the door_lock_nus example to add the set pin command (0x05 from zcl reference). So I have modified the zigbee callback to read the new...
Hi,
I am wondering how to let these both run together. If I understand the sdk_config correctly the app_scheduler event queue can be used for the USB directly. But how should...
When performing a DFU the 2nd stage increments the expected device BLE address by 1 when the device being updated reboots. This potentially conflicts with the address of an...
