I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi..
I am working nrf52832 with accelerometer sensor, I want to store the data about 100hz for 1sec in flash, I want to store it an array and send it over ble how to do...
- I used https://github.com/NordicSemiconductor/Android-BLE-Library version 2.1.1 and https://github.com/NordicSemiconductor/Android-Scanner-Compat-Library to code My Ble...
We plan to develop a temperature and humidity sensor based on nRF52832, which needs to evaluate power consumption to confirm battery selection.
are there any similar data...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
I'm trying to optimize an Azure project based on the Asset Tracker example. I was recommended setting CONFIG_SERIAL=n in both the Application FW and SPM. However when I add...
Hi,
I based a new device design on the Thingy91 antenna and tuning circuitry and noticing that the current consumption of the two QM12038's negates the amazing power efficiency...
1.In docs I see: “This example requires one of the following SoftDevices: S112, S132, S140”. What is the reason not to support S113?
2.Is there a way to accomplish functionality...
The Cloud_client sample application does not work in this version.
The connection with the nRF Cloud is disconnected immediately:
I: Network registration status: Connected...
Hi, I am trying to add a secure button less OTA service in my application.
1-I have successfully added service but showing the following error.(I can see OTA service in...
Hi,
We have been working with a Zigbee coordinator based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b, Softdevice and FreeRTOS.
Zigbee task defines a...
Hi,
Is it possible to add a custom characteristic to a standard BLE service? I wish to add a CO monitor with ESS (0x 181A ). If yes, how to add a 128 bit UUID with this...
Hello,
I want to output in one pin 400kHz and inverse of 400kHz in the other pin. I have somehow managed to output the the 400kHz but haven't managed to output its inverse...
I'm trying to implement advertising only on a single channel
Here is my initiation function
but ble_advertising_init is returning err_code 0x00000006
I believe it...
Hi everyone,
I have come across the FPU_FFT example project for nRF52840. Just for curiosity - I'm HW-guy - I'd like to evaluate FPU's performance - to see how many instructions...
