Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello,
I'd like to understand a bit more about transmit buffers for sd_ble_gatts_hvx() calls. Our peripheral application is developed using SDK 15.3.0 and S112 for nRF52832...
Hi,
reading through the gnss socket configuration parameters it came a question to my mind regarding the Power Save Modes.
Is the PSM configuration applied when the GPS...
Followed the example https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/spi
but getting spi received value 0xff each time
my conf file:...
Hello, I am a bit confused with the ARM Cryptocell 310 engine. As I can see this software is proprietary but in nrf5 sdk there is the cryptocell engine as external library...
Hi,
I am using nrf52810 ,softdevice 132.
I am trying to implement whitelist in ble_app_uart code (peripheral side).I take reference from HID mouse example.
Code compiled...
Hello everyone,
We're looking to develop a prototype of a very simple panic button. The device should automatically pair with iOS / Android, and establish a call to a given...
I have an example application executing on the nRF52840-DK on SDK15.0.0, see https://devzone.nordicsemi.com/f/nordic-q-a/67351/are-there-any-differences-between-sdk15-and...
When we try and stream BLE data to the nRF Connect app on an Android or IOS phone the app accepts our requested for an MTU of 244 or 160 respectively, however it does not...
Hi,
Dev setup:
Segger embedded studio - fatfs example - SD card - nrf52832
I am able to write to sd card and see data. But while reading i am failing.
Below is code...
Hi,
I am a bit confused after looking through all the SDK solutions available for NRF52 and need a piece of advice...
I am have started on the project that consists...
Can I periodically or continuously read the characteristic of peripheral after the connection?
If there is a change in the value in peripheral, then the value is received...
Hi,
i am trying to do buttonless dfu . I want to merge all hex files into one as per the document .when i enter the mergehex , i am getting mergehex command not found why...
Hi,
I'm making an new board with both nrF52840 and nRF9160. In addition to the radio ICs there will be some antenna diversity switches, chip antennas etc.
So I'd like...
Hi,
I'm using SDK 15.2 with Nrf52832,
I've implemented a custom service with read, write and notification services.
I would appreciate if you could send me an example...
