Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
We are looking to implement "dynamic" BLE services that can be configured (i.e. enabled/disabled) externally, however from the examples there appears to be no way of de-initialising...
Hi,
I have nRF9160 DK. I want to update firmware to (From Your WebSite: Link Pasted)
nRF9160 LTE-M/NB-IoT/GPS Modem firmware
https://www.nordicsemi.com/Products/Low...
Since nrfConnect Programmer, ninja flash/west flash ALL use nrfjprog behind the scenes, I wish I could find out _exactly_ which nrfjprog commands the nrfConnect Programmer...
Hi,
I'm trying to reduce the current consumption. I can't use sd_power_system_off because I don't want my device to rest when it wakes up. So the other way to do this is...
Can i commuicate over USB CDC on holyiot nrf52480 by giving Vbus(5v) , D+,D- , gnd from pc. and get output on VDD or do i have to also supply voltage on VDD(3V) ? I wanted...
Using nrfx_timer_extended_compare I would like to periodically adjust the compare value of a running timer. It seems to work without disabling the timer before this and re...
Hi，
Dear， I have a question about Fstorge and Bootloader. If my app layer calls the Fstorge API to store some data, will the data saved by the Fstorage API be erased when...
Hello All,
I am running into a mesh assert error when running the light switch server demo on a custom board w/ the NRF52840 (MDBT50-1M). The device starts up fine, has...
Hi all
I am studying mesh example such as light switch server, I use Segger Embedded Studio to comple the project of light switch, it is OK, but when I want to do online...
Hi,
I'm developing a BLE DFU controller with bluepy on a RPi3. The peripheral that is being updated is a nRF51 device on SDK 12.3.0, with the secure bootloader and experimental...
Hi,
In our project we want to use nRF52832 chip using HCI Command interface. We are trying to use Zephyr RTOS project for geting HCI interface through UART. We are using...
Hi,
In y project, I want to implement CTS. Until now it's been working, but I don't know why, I now have this problem: Current Time Service not found on server, which means...
I am using a Sparkfun Pro nRF52840. I wish to communicate with it serially. I found the UUIDS it exposed : UART Service = 6E400001-B5A3-F393-E0A9-E50E24DCCA9E TX Characteristic...
