I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to drive a servo by the PWM on nrf52832. The pwm cycle is 20ms and the duty is 1.5ms. But i have a problem that the duty is not precise when the BLE is working. I need...
Hi,
I am using a Sparkfun nRF52832 Breakout board with the Arduino IDE. My objective is to control 3 SPI digital potentiometer. The problem is I don't know how to select...
nRF52840
SDK15.3
My question is regarding the low frequency clock.I am initializing the low frequency clock as follows:
When TASKS_LFCLKSTART is initiated in line...
Hi Nordic,
I have been trying to communicate with KX 124-1051 using IIC in nRF52832 . I am getting NACK from slave every time i send the device address. I checked all the...
Hy to everyone
I'm working with SDK15.3 Ble_Blinky example for my nRF52840 Dongle (pca10059).
First to know, I'm wokring with c++ and the whole Project is compiling without...
I'm using this module to develop a toy that needs a couple of sound effects. I just don't want generated tones but previously recorded audio files no longer than one second...
I wanted to try the bootloader related example. I was using the IAR to run peripheral examples.
But for bootloader example, I saw that IAR was not listed. So installed the...
I read the following QA - https://devzone.nordicsemi.com/f/nordic-q-a/41237/on-dfu-jump-address but still have doubts
1. Is it safe to set the Bootloader RAM start address...
Hi,
Hardware：nRF52840 module, Power Profile Kit. SDK：nRF5_SDK_15.2.0_9412b96.
Using Power Profile Kit to measure the low power consumption current of an nRF52840 product...
Hi,
I am currently trying to use SDK 15.3 secure serial UART bootloader (from the example in nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040_uart) on a custom...
hi, I am working on the bootloader with s132.5.0.0 on sdk14.2.0. I am trying to using the uart to flash the chip.
I build the bootload example bootloader_secure_serial,...
I'm using three PCA10056 boards to test mesh example(Meshv3.1\light_switch).
[light_switch_client] ---> [light_switch_server1] ---> [light_switch_server2]
*Put the server2...
I am testing a mesh network, using the NRF52832 modules, SDK 15.2 and MESH_SDK 3.0, provisioning the nodes with nRF Mesh android app and using a modified firmware for the...
I am trying to build UART support into my current project but the compilation of the nrfx uart driver fails. See error below:
Any idea how to solve this? Is there good guide...
Hi,
I'm using the NRF52840 with the "nRF5_SDK_for_Thread_and_Zigbee_2.0.0".
I tested the zigbee light_bulb example and zigbee light_bulb + ble. It works fine so my next...
