Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi I am using nRF52832 .My application acts as central and Peripheral at the same time.
board acting as Central: scans and connect to peripherals without any error.
But...
Hi,
I'm using nrf52840 and a barcode reader by UART using softwareSerial.h library, it works fine. I am also using the bluefruit.h library to communicate by bluetooth that...
I'm modifying the DFU example app in SDK 15.3, for the nRF52840.
attempting to call fds_record_update or fds_record_write within the context of app/main.c ble_evt_handler...
nRF5_SDK_11.0.0_new\examples\ble_peripheral\experimental_ble_app_eddystone\pca10028\s130\arm5_no_packs
Using the above mentioned example on a custom board with nf51822....
Hi,
I am working on a custom board with the 52840 chip. The problem I'm facing is that when I plug in my custom board, Windows 10 immediately shows a USB malfunction error...
Before my 52840 acting as central is connecting, it scans with the following params list:
static ble_gap_scan_params_t const m_scan_params = { #ifdef BOARD_PCA10056 .extended...
Hi i am using nrf52840 DK and i am trying out sleep_mode after timeout happens. but i had a doubt in ble_adv_evt_idle i.e if i use this case the device goes into sleep and...
Dear all,
I have a problem.The DFU could not be performed due to a large size of the application around 300kB.
Platform : 52832;
SDK: SDK_11.0.0;
softdevice:s132.
If we edit the example code in seggar embedded, are the same changes done for the hex files of the same examples? IF not how do we change the code and put it in the dongle...
Hi,
I was following the instructions laid out in the "Configuring DFU over Mesh" guide in the nRF5 SDK for Mesh v3.1.0 ( https://infocenter.nordicsemi.com/topic/com.nordic...
Hello All,
I am working on nRF51822 custom board and i am not change it because it is customer requirement. Use IAR embedded workbanch IDE in windows 7. For reference...
This post mentions that only logical address 0 is supported for the coded PHY.
Is there any additional explanation for why this is? The OPS does not mention this.
...
Hello, I am working on a project based on a central/peripheral NUS application, with nRF51822 and SDK 12.3 .
I Want to know if the debit of data exchanging is lower when...
Hello,
I have configured the toolchain and SDK by following the NRF Connect getting started guide and followed the below steps to compile the mqtt_simple application (on...
Hi,
i m using central and peripheral code in SDK15.3 version,and i am not able to send or receive more than 20 bytes at a time in nRF52840 chipset.We are using Master...
