I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
I am developing a firmware to count pulses through a GPIO and store the sum of these pulses in a memory until there is pairing with the BLE. After pairing, the sum...
Hi
At the company I work for (Ztove ApS) we have expanded the capacity of nrfutil (https://github.com/NordicSemiconductor/pc-nrfutil) to include a option for AES (CBC mode...
Hi
In ESB there is the function nrf_esb_suspend(). After calling it, what function do I call to resume ?
Look forward to hearing from you
Regards
Mahendra
Hello!
Related to the addition of new services to the Attributes table, is there a way to check if a certain service UUID has already been added?
This problem arose because...
How do I check what version I have installed?
The 'Getting Started' page states a minimum version of 9 .5. 0:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom...
So what steps do we need to take to have these two different Python versions both installed & usable at the same time on the same machine?
The ' Installing the toolchain...
I have three PCA10056 development boards and have loaded the BLE mesh light_switch proxy_server onto all of them (SDK v2.2.0) which incorperates soft device S140 V6.0.0
...
Hi all !
I'm struggling to get a frequency jumping protocol up and running and can't figure out how to handle the following situation (please refer to the attached "pseudo...
Let's have light-switch provisioner, server and client.
My question is, how to send a message from a client or a server to the provisioner? In order to send a message, client...
Hi,
As part of my project, I need to use the SD card drivers of the nRF5 SDK and the I2S driver. The issue I am having is the following:
If I use pin 31 as the SCK signal...
Hi
This is a heads up that in SDK15.2.0 and file nrf_esb.c you have the line
m_rx_fifo.p_payload[m_rx_fifo.entry_point]->rssi = NRF_RADIO->RSSISAMPLE;
it should actually...
Hi
My application uses NFC for various reasons, and I need, at runtime to load up to 4 textural NDEF records onto the Nordic NRF 52832's NFC hardware.
If I wanted a simple...
Hey there faced with the following problem:
I have two hardware setups:
1. Laird DEVK-654 (nrf52480) without external oscillator
2. Laird BL654 mounted to a carrier...
I added the Generic OnOff Model from the thingy52-mesh-provisioning-demo to the Light Switch Proxy Client example from the nRF5_SDK_for_Mesh and get a linker error for the...
Hi All, I am polishing the code that we have, working out minor bugs, etc, we use Nordic UART to exchange data between our device and smartphone or tablet, sometimes data...
