I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Good day,
I want to use the Bluetooth Low Energy App of the nRF Connect for Desktop with my nRF52840DK as a local device.
After I have connected my device (nRF52840DK...
Hello,
I am using the NRF52840 with the flash chip W25Q32. I tried using the sample program "Flash Sample" with my device set in qspi. I can get the flash device reading...
Hello and thank you for reading. We are using SDK 2.5.0 and the nrf5340, and would appreciate some help with the HID over Gatt functionality.
Our device implements multiple...
I have an application for a mouse with nRF52833, s140 and SDK17.1. The BLE advertising works in fast and slow advertising, and I'm following the indications by Microsoft on...
I'm trying to port a PPI application to an nrf5340. I'm quite puzzled, as it would appear there is no obvious way to achieve what I'm trying to do.
In short, I have a setup...
Hi,
I notice that every time I can only send 244 bytes per time in nus service, if I set higher I will not receive the data in RX.
But I also see that the thoughput...
Hello,
We're using version 7.0.1 of the S140 soft device. We are making a bluetooth application where the device behaves both as a central and peripheral. In peripheral...
we now have nRF52840 DK PCA 10056 , V3.0.0 . the documentation of product specification user guide available online is for v1.0 (old dk) , but not for v3.0 . please can you...
Hi folks,
I am just in the process of getting my feet wet with the nrf connect sdk and zigbee development is my ultimate goal.
I am using an ItsyBitsy nrf52840 https:...
Wireshark Windows version 4.4.5
nrfutil 7.12.0
ble-sniffer version 0.14.1
Somehow during the course of installing the nRF Sniffer, Wireshark got two interface toolbars...
Hi,
I'm working on a very high density board with the nRF54L15-QFAA (we want to prevent using a CSP) and I'm running into some routing issues. While looking for optimizations...
Hello, We faced with issue in which we are not able to get the time from the network and because we don't have time, we can't use JWT. As I understood issue is because of...
Hello everyone, I am want to write custom radio protocol for the nrf5340. I have already tried the ESB protocol. But that is somehow limited on the latency (I will open a...
I'd like to use the nRF52832 for cost reasons & I know there are different Bluetooth audio standards, which the nRF52832 does nto support the latest. I don't need hi quality...
Hi, I have a question about the WDT documentation in nRF5340 Product Specification v1.6.
Question 1:
The chapter "Reload Criteria" (7.41.1) is maybe a bit ambiguous defining...
