Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi, may I looked bad , but I can not find NTF52 documentation, datasheet, evaluation board schematic, pinout, price... nothing , except the file nrf52.h in which I found some...
The following SDK files have incorrect comments:
markrages@qountdown:~$ grep 'units of 0.625' -r /opt/nrf51sdk-11.0.0 | grep 300 | grep to\ 25\ ms
/opt/nrf51sdk-11.0.0...
I configured nrf to go to sleep after 5 minutes of inactivity and then wake up by external signal (by accelerometer interrupt if any movement detected). what struck me is...
Hi again,
I'm here with another HID problem. When I flash my chip with standard HID mouse example, OS discovers it with it's declared in code name, connects succesfully...
I have designed an custom application board based on nRF51822 SoC,
Now i wanted to do testing on RF front.
I found one Test guideline(RF_Performance_Test_Guidelines_v1_0...
Hello Everyone,
I am able to do this functionality by using NRF5DK
Using Android APP (MCP master control panel) am able to make beep sound in the NRF51DK by using...
Im working with a nRF51422 EK. So, there is an android application with 2 buttons. Each of them can Set a LED. It will be set as long as the button is pressed on the application...
SDK:10.0.0
Here is the error when I compile
..............\components\softdevice\common\softdevice_handler\softdevice_handler.h(40): error: #5: cannot open source input...
Hello,
I have a project which is currently using S110 SoftDevice v7.1.0 with nRF51 SDK v6.1.0. The hardware is nRF51822 xxAA revision 2. It will probably be upgraded eventually...
Hi,
I intend to use ANT protocol for an application of soccer players trackers.
Each soccer player would wear One master and remote sensors communicating with ANT.
But...
Is there a way to know if we are in critical region?
ie: between sd_nvic_critical_region_enter(&foo) and sd_nvic_critical_region_exit(0) without explicitly using a global...
Hello,
I'm using nRF8001 with Arduino for our project. I use BLEeripheral. h and I need to know if it's possible
with the visibility of NRF
when invisible can nrf...
Hi,
everyone,
I am new with the uvision IDE.
Can anyone tell me how should I supply source and header file to project so that my header files can be access without relative...
I'm curious. I believe I can set it up in the keil "options->target" tab.
I get it that as long as I don't cause the softdevice and my program to "overlap", it is fine...
