I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
HI:
everyone!
How to make the matching and binding equipment information would be stored permanently, even after the OTA upgrade is still in;I made with examples of the...
Greetings, I tried to modify the parameter "len" to anything over 1 (byte), but it just doesn't work.
As long as it's over 1 byte, the API crashes my program. err_code shown...
Hi,
I'm using s130 as softdevice for nrf51822. I program the softdevice with the official s130 hex file. According to the hex file, there is no data at address from 0x7c0...
We're working on an application that needs ultra-short range BLE, on the order of 50cm radius or less. I've found little discussion anywhere on that topic, likely because...
I notice that the dongle has a 3.6V-5.5V input and a pin that sais 3.3V, I measured 3.3V on this pin so I was curious if I could run an IMU unit and an i2c/spi bridge requiring...
Hii all
I am trying to port the experimental/bootloader_signing project to gcc I made changes in the project accordingly, so now its working. I can able to flash application...
I connect a GPS module to nRF52 DK and connect nRF52 DK to my computer once more.
GPS module ---> nRF52 DK ---> computer. (like this)
So I want to do NMEA parsing like...
Dear All,
I am sorry but I have to ask this question here, I searched and red trough the forum, tried the suggestions, nothing works.
Basically I want to have a HID device...
I use softdevice 6.00, size is 80K Byte. I use the chip NRF51822ab,and configurat the irom start at 0x14000,size 0xC000, IRAM, start at 0x20002000,size is 0x2000 ,in keil...
Hi,
Is there a possibility to read the state of the gpiote pin? (is it high or low). Is there any function or any other way to do that?
I'm changing the gpiote pin via...
Hi,
I made a own service for a rotary dail in a peripheral(S110). This service send the speed, direction and a counter (all uint8) of de rotarydail in separate characteristics...
Hi Everyone ,
We were using nrf51822 rev1 IC for our project and now it is changed to nrf51822 rev3 . Previously we were able to detect the chip in nRfgo Studio on our...
I am looking for a device with support for the 4.2, long packets (up to 255 bytes) feature. I see that the nRF52 is a 4.2 device. But for what I understand the optional long...
I am using s120 for central device, and my central device connects to multiple BLE slaves. After connection, some slaves may lost connection due to power off of that device...
I want send ble bond connection request from raspberry pi to nrf51882.
Can you please let me know which ble libraries I need to send central ble bond request to nrf51882...