Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hello,
I try to generate 4 PWM signals on an nRF51 DK board, but I have two troubles :
in the "Simple PWM", during nrf_pwm_set_value() function the TIMER is stopped...
Hi,
I recently ordered a usb dongle. It has PCA10031 board. The chip shows "N51422 QF ACAB" printed on it.
What SDK should I use? 6.1.0?
What board file should...
Hi!
I am using nRF51 SDK v6.10. I try to analysis the "spi_master_example". Source codes is
working well. But I couldn't understand how the "spi_master_send_recv_irq(...
I have an android application, which one can set and unset the LEDs of my nRF51422 EK. But sometimes when I click to fast the command will not be send. So I would like to...
Hello,
I want to know if it is possible to configure a button to act with different Detection delay.
In other words I want to have a single button to be able to trigger...
Do we have KiCad version of nRF51822 QFN48 reference design? We looking at open source toolkits, including Eclipse, so KiCad comes into picture.
Thank you in advance!
The test code:
int main(void)
{
sd_softdevice_enable(NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION, softdevice_assertion_handle);
temp_init();
unsigned int aaa...
I have a follow-up to this question: devzone.nordicsemi.com/.../
We are interested in dynamically changing the supply voltage because our space-constrained design requires...
Hi,
For my custom PCB, I am using the PCA10004 as reference in order to determine if the maximum possible range has been achieved. However, I am seeing only about 20 feet...
Hello I'v just ordered a NRF51-DK kit.
I'm looking at the different tool chain. In my application speed is critical 16Mhz is actually bearly enough, so my question is:...
I have a USB dongle with an nRF24LU1p that has a few SPI pins but is missing the RESET pin. I would like to be able to program it via SPI but the SPI programming protocol...
nRF51 RTX 4.74.0-3
SoftDevice S210 V4.0.1-3
Created a timer for 5 seconds interval.
It turned to be 4.4 seconds. with or without softdevice enabled.
Anybody else has...
Hi,
Access to the UART hangs the execution of the experimental_ble_app_uart_s110_pca10028 example.
The phenomen occures In the file simple_uart.c when checking for the...
This may not be a major disaster,but it bothers me:
I have written an application to read data from an ADXL345 accelerometer (using SPI) and print out the data on a console...
Good morning,
i still couldnt find out if it is possible or recommended to use the PPI together with the s110. i checked the example in the sdk documentation but it was...
