My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
on your item nRF52-DK
there are differents between Resision 2.1.1 vs 3.0.0?
V 2.1.1 ==> Chip ATSAM3U2CA-AU of Microchip is alone to provide "programmation/debugger segger...
Dear Mr/Mrs,
Our commercialized product currently have a default: some (luckily rare) clients get a crash after the 1st configuration - sometimes hours after but always...
hi support team,
customer 52832 product had problem that they can't pass fcc test,the reason for this is they forgot to add capacity to those pins.
their design is:
...
Hi，When installing the nrf5340 development environment, the tool chain is installed and the "getting started assistant" check is also passed. However, there is no NRF related...
By default the Thingy91 has many useful factors it can measure:
Pressure, Humidity, Temperature, Light, Position, Button, Flip, Signal, Voltage ...
I really only need...
Hello,
I want to design a board with nRF52832 or nRF5340 which contains several sensors, QUAD or regular SPI flash memory, and a TFT LCD. This TFT has an SPI connection...
Hi,
I am new to DevZone as well as BLE development itself. I am currently working on a project and trying to undestand the IDE as well as the processes and workflow of the...
Hello Community & Nordic support, Observed behaviour: my project build with nRF Connect SDk v2.1.1 was with errors
expected behaviour: my project build with nRF Connect...
Hi,
If I run my nRF5340 peripheral BLE NUS service with NCS 1.9.2, I get two different behavior at console.
When I connect from my WIndows PC running nRF Connect for Desktop...
I'm not sure if this code I inherited is using k_poll_signal correctly because it seems like I can handle it in a much simpler way with an atomic variable.
The below code...
I want to use the lsm6dsox IMU on my Adafruit feather nrf52840 sense board, and I should use other I2C, other than p012 and p011, to not have a problem with the other IMU...
Dear team,
I am not able to flash the nrf5340 audio application (gateway) to the nrf5340 Audio DK using SWD from nrf5340 DK. I nrf5340 DK outputs 1V8 logic.
I can see...
I am using S132 in the Segger IDE on an nrf52832.
I am using SDK version 17.0.0_9d13099.
When I call sd_ble_gatts_hvx() from within a GPIOE ISR (externally pin triggered...
Hello,
Looking to see if there is a pinout TABLE for this package. I've seen the schematic drawing already but looking for a table format which is more user-friendly when...
