Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
My project uses nRF52832 and I'm at the point of the project where I'm trying to minimize power consumption.
To assist in this, I created a very small main() that goes through...
Dear Support,
I have tried to find the correct info to integrate the DFU functionality of the nRFConnect app on the phone into our own mobile app. We want to be able to...
Hello
I am using the NRF9160 and I can see that modem RF transmitions cause some EMI issues
I would like, for a period of few seconds each time to stop modem transmitions...
Hi, dear Nordic team,
We've already purchased a few thousands of BC805M BLE modules (nRF52805) for our upcoming mass production. During R&D, according to datasheet, we...
I need to use Delay of few Micro/ Milli / Seconds without pushing the MCU in sleep i.e. without using k_msleep() etc. Is there any library for this purpose in Zephyr ?
Hi, Hope you can help. With a nrf52840dk development kit arriving tomorrow. We tried to make a start with a nRF52840 dongle, which we eventually want to use. Connected to...
Hello,
I follow the doc to install the nrf_sniffer_for_bluetooth_le_4.1.0
- Flashing the nRF52840 dongle with nRF Connect for Desktop
Uploading image through SDFU: 97...
Hi,
I'm trying to use a nRF52840DK as a zigbee router implementing a temperature sensor. The setup is composed of
Software
Application: Home Assistant
SDK: nRF5...
Hi, I'm trying to achieve high throughput of BLE on connection between two nRF52840 DK.
I've read some articles about it, and configured both Central and Peripheral devices...
Hi,
I'm looking at the nrf5340 PS v1.2, page 75 & 76 regarding the audio clock PLL. Using the formulae given, I'm finding that the register value that yields the closest...
Very much a beginner at this so if this is inappropriate for this forum do not hesitate to let me know.
Starting out trying to develop a BT Mesh system. I purchased a nrf53...
Hallo Dears,
I would like to develop a ble-peripheral role device with a humidity sensor service. I found the development kits from the nRF5x family such nRF51, nRF52...
Hi,
I'm trying to take advantage of nRF52840 as Zigbee NCP in communicate with a host microcontroller via UART. My problem is I don't know what I have to send and what will...
Hi,
In your LE audio presentation from CES that you had a demonstration of a low latency setup with LE audio. We are more curious about the setup you demonstrated so we...
I have built and successfully run this application with the nRF Cloud and then I achieved a partial success with running this application with the AWS IoT.
When I run this...
