My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
Hi Nordic Team,
My dev environment is as follow:
nRF52832(ble central)+ S132+ SES
We are using BLE Chip on a custom board.
When we flash hex file ( softdevice hex...
Hello,
I am currently evaluating whether the WiGLE geolocation interface is something that the nrf9160 can support.
One of the required pieces of information for that...
Hi,
I am using AFE4403 and Nrf52840, I want to assign a pin as output oscillator 4M using a nrf52 internal oscillator,
how to do that?
I am beginner , is my first...
Hi Everyone,
I'm not able to start ble scan. I've followed following example...
Developing Bluetooth Low Energy products using nRF Connect SDK
https://www.youtube.com...
Hello,
I was trying out sending RR intervals on the Heart Rate Measurement service and seeing what happens in nRF Connect. But, something is weird with the way the values...
I have a client project developed in 9160 which needs to be connected to the network via NB or LTE-M. Before each connection, I read imsi to determine the apn of the carrier...
Hi
Im trying to get the mcp2515 candriver example to work https://github.com/nrfconnect/sdk-zephyr/tree/main/samples/net/sockets/can#id3 .
i have some error during build...
We have an nRF52 with dual roles: peripheral for the connection to an app, and central, connecting to multiple third party peripheral devices.
We have come across a very...
Hello,
I'm using Segger Embedded Studio (SES) (on Windows 10) with nRfConnect SDK and nrf5340 processor.
In SES I can oben a graphical view of the configuration through...
Hi, I have developed a firmware on nRF52840 as central ble_app_uart_c\pca10056\s140. Now I have to upload it in nRF52810 which soft device should I use? Thanks!
Hi all,
I working with NCS v1.7.1 on a custom board using nRF52840 and I am trying to enable a 2-stage bootloader setup using NSIB as the first stage immutable bootloader...
Hello sir,
I am using the nrf52832 Dev board and try to send the data through custom value update then the following error occurs as ERROR 8 [NRF_ERROR_INVALID_STATE].How...
P0.25 is accessible by below:
nrf_gpio_pin_set(25);
However, when I try to access P1.00: Neither this:
nrf_gpio_pin_set(1); Nor this works:
nrf_gpio_pin_set(32);...
Hello, we have a device that uses the nRF9160 with an external GPS receiver that is controlled over I2C. I have connected the LNA enable pin to COEX0 on the nRF9160, but it...
