I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hello,
I have been using the TWIM peripheral of the nRF52832 (via the twi_mngr) to talk to an accelerometer and a magnetometer. I have 4.7k ohm pullup resistors (in parallel...
Hi,
I am using nrf52840 customized dongle in our project. We have interfaced ADS1118 using spi communication with nrf52840 (customized dongle). The problem here with the...
I am trying to build the 'BLE NFC pairing reference' example for nRF52840.
I downloaded the latest SDK and located this example in the experimental directory under BLE\Peripherals...
nRF52840
SDK 15.3
Segger Embedded Studio
I PWM a piezo buzzer (with a transistor) , using the PWM peripheral. The problem I encounter is that before I call the PWM...
hi support team,
i have a wired problem that i can't explain to customer:
first, i test this project "nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hids_keyboard...
I was able to successfully use the example ble peripheral blinky firmware example with the blinky mobile app. I added peer manager for passkey pairing but the blinky app is...
Hi Nordic Team,
I am using ble_advertising_advdata_update() to update some of the advertising data. I am doing every time the device is asked to advertise. In my code I...
the following report map is working when i try to increase volume on windows system (send 1 byte == 0xe9)
0x05, 0x0c, // USAGE_PAGE (Consumer Devices) 0x09, 0x01, // USAGE...
Hello,
my question concerns the layout of a bluetooth antenna & tuning circuitry for an nRF52832. Specifically, about two separate concerns:
1) Due to the shape of the...
Hi,
I want the received the datapacket from bluetooth to be stored in eeprom and access it when need be .If you have any small exmple codes for the same kindly inform me...
Hi,
We are migrating code from NRF Connect sdk 1.3.1 on nRF52840 to NRF Connect 1.6.1 on Nrf5340. Using SoftDevice as BLE controller on both.
Our existing code uses a...
Hi,
I want to run my application on the latest open thread libraries.
As per the page "infocenter.nordicsemi.com/.../thread_ot_libraries_building.html"
we need to run...
Hi,
We are using the nRF52840 Dev Kit with SDK17 and SD140 without FreeRTOS. There has been discussion in other postings <link> about increased current consumption caused...
Hi,
I am having a NRF9160DK board , which i want to use it for an simplest BLE application which sends the data from NRF52840 to my mobile using a simple BLE application...
Dear sir/madame
In our project we want to implement MAX17260 battery fuel gauge to monitor the battery status in the handheld device.
The interface towards MAX17260 is...
