I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hi, I've recently been diving into the whole trustzone implementation on Zephyr and I'm having trouble understanding how to properly work with it.
My question is fairly...
I'm using the default implementation of the Peer Manager module. I see under the hood it uses the FDS module to handle Flash Write/Reads. If I wanted to implement some Flash...
Good evening,
I am using a nrf52840DK to set up a product prototype and I have a couple of questions about the peripherals. My nRF Connect SDK version is 1.5.99.
1....
Hi, Iam working on creating a ble mesh network. I wanted send led status whether on/off message from server to client periodically like every 10sec. I have configured the...
Hi I'm learning Zephyr ecosystem in context of using nRF SoCs. How one can achieve current consumption values as low as in datasheet ( 0,4 uA in System Off, with no RAM retention...
After nrf52840 uses the SPIM3 peripheral to send data, turn off the SPIM3 peripheral to enter low power consumption, and there will be 700UA current; if the SPIM3 peripheral...
I am trying to read data from a chip over SPI.
The implementation of the SPI comms is not ideal as they require a new CS/SS line toggle on every byte. I cannot do a bulk...
I hope that someone can show a clear example of this. I surprised that it isn't in the SDK examples. Basically, it is necessary to stop the BLE SD, in most low-power examples...
Hi,
I am having a problem where the client is unable to receive notification from a peripheral after the softdevice in the peripheral returns 0x3002 after a disconnect....
Hi,
I am trying to implement DALI-104 (IEC-62386:104:2019) on top of openThread protocol.
I am using Thread: CoAP Client and Thread: CoAP Server and want to configure...
I am Rattana. I have some project for Bluetooth communicate with mobile phone. Then I will use BC805M(nRF52805).Nomally I connect my MCU with HC06 and I use MCU because I...
Hello I'm now trying to implement the IOS Phones (Central) - Device (Peripheral) liver UART using Multiple Connection - Nordic Uart Service. Devices tried to send a UART signal...
Hi,
We are following the project CHIP and planning on design a matter device with our existing hardware platform. The below are some questions about it:
1. Our platform...
Dear Nordic Bluetooth Experts,
My project is quite simple: A BT Mesh device (generic level server model) powered by a Nordic nRF53832 and an Android app that is used to...
