Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I want to update NCP application in the field. NCP is attached as USB device on Raspberry pi which act as border router.
I am using open bootloader ( pca10059_usb ) and...
Hello.
We are currently developing PCB design of smartwatch with RF Nordic nRF24 chip, Johanson small ceramic antenna (P/N 2450AT42B100), and capacitive Touch Switch (AT42Q1012...
I am using asset_tracker as the basic program and basically it is running fine and sending data to the RF connect web page.
However approximately every 30 minutes I get...
I am looking for a simple example for I2C write. The TWI sensor example is not clear.
It would be great to have an example like the basic SPI example
i.e.
How to init...
Hi, My company is interested in doing bluetooth beacon location tracking of android devices for a VR project. I notice we can easily purchase bluetooth 5 beacons on amazon...
Hi,
I am trying to migrate my project file from Keil 5 to Segger Embedded Studio (SES).
After porting all my source code and configuration files, SES is able to compile...
Hello,
I want "nrfutil" CLI tool (To perform DFU OTA of BLE) for one of my device which is based on i.MX6ULL ARM based processor 32bit.
I found that using "pip install...
Hi,
I am using nrf52840 chip, there is Thread and iot coap library, and movement sensor. When sensor detect move, pin call interruption and send coap message.
Voltage...
Hi all, Within my application I've followed the example/fstorage to the letter however upon requesting a flash write to the s112 the nrf_fstorage_is_busy() function loops...
Hi,
I am working with nRF PCA10056 evaluation board and using SDK 15.2.0. I am using nRF52840 as a central scanner, where it will scan broadcast data from beacons.
I want...
Hello,
I'm having problems with resuming usbdevice from susspend state. I'm working on SDK 15.2 with SD140 (6.1.0). on custom board with nRF52840 IC rev. 2.
My application...
Hi, the power LED no longer turns on on my nRF52840 DK board. The board is still advertising when it is connected to a power source and I am able to connect to it with a mobile...
I'm trying to add PDM into my project but can't get it to compile. When I try to call
I get the error "main() undefined reference to `nrfx_pdm_init'"
This looks like...
Hi,
I have some code written to copy PDM mic data into the external and then later dump it over UART. The issue I have is that when using the external flash, my audio...
