Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am working on a product based on an nRF52832 (SDK 15.3, S112 v6.1) with Secure Bootloader.
I am trying to enable the peer manager with bonding using the Flash Data...
I am starting a new development and want to select an appropriate debugger. I am using Keil uVision Pro version.
I a previsous project I was using ULINK2 and was hoping...
Dear All:
I want to learn the detail of the ble technology and i think the offical ble sniffer is very cool, but it is not open source, so i want to write a ble sniffer...
development environment： SDK 15.2
I am trying to make app_ble_uart.project can be bond with my Android phone, but everytime i press "bond" button by nrf Connect APP
sd_ble_gap_sec_params_reply...
Existing method: Search equipment in app and try to connect.
Question: can I search our equipment in Android OS Bluetooth setting and pair?
The customer wants to be automatically...
I am developing a NIR (Near-Infrared) product using nRF52810. I use 15.3 for SDK and S112 for Softdevice. I implemented ADC (saadc) function based on ble_app_uart.
I have...
Hi everybody,
I been experimenting with the HID over GATT example (mouse), and I am trying to use more than 3 report IDs. When I used only 3 there's no problem. But when...
Hello DevZone,
SDK 15.0.0. SD132 PCA10040
SPI settings : Mode 0, MSB first, 125kbps, orc = 0
I am trying to get NFC communication between two dev kits, one using the...
Hi,
is there a possibility to tune the external xtal (lfxo) or the rtc?
In other microcontrollers there is a possibility to trim, for exampe the rtc ignores one or more...
Hi teams,
I have build custom board connected to ethernet via ENC28J60 ethernet controller.
It uses SPI communication with ENC28J60, but some strange behaviour during...
hello
i am using nrf52832 with pwm driver (working with ble and s132 if it metters)
i need to control 4 different motors speed via pwm, since there can be only 3 instances...
Hi
I have implemented a scannable advertising on nRF51822, s130, SDK12,
I can see it's working by reading the scannable information on nRC Connect, however,
on the sniffer...
Hallo,
I have a question reading the datasheet. It states:
" If a regulator is only to be used in LDO mode, the inductor for this regulator is not needed. "
I want to...
