My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
Hi, I tested the TCP client AT command in nrf9160DK, I flashed the ncs v2.5.1 example of serial_lte_modem firmware on the board.
I send the command as below list:
AT#XSOCKET...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
< Simple Code Explanation...
Hello
We are using nrf5340 in the new project. PCB design was made. We are currently waiting for the typesetting process to be completed. There is no Jlink on the designed...
Hello, I have a few questions about sending code via J-Link. We are doing our project on vscode with 2.6 sdk. When working with nrf5340dk, flash via vscode was enough. However...
I recently enabled power management in my code base by adding these two oiptions to my prj.conf:
CONFIG_PM_DEVICE = y
CONFIG_PM_DEVICE_RUNTIME = y
The code runs...
Description : I am experiencing a build issue after porting my project from nRF SDK 2.4.2 to nRF SDK 2.7.0. The project involves using the nRF5340 and was building successfully...
Hi,
My nrf9160-DK version is PCA10090, 1.1.3, 2023.31
I am trying to test the esim, but the firmware tells me no simcard found. After doublechecking the esim soldering...
SW version :2.4.0 HW revision: nRF52833 development board, PCA20054 Direction Finding Antenna Board 1_0_0 I use the routine director_finding_central and director_finding_periopheral...
I am getting an fs_close() -5 error (-EIO) when I write to an SD card using fatfs. I determined this error was associated with FR_DISK_ERR in fat_fs.c.
Additional info ...
Hi, im working in a project with the nRF5340-QKAA and I need VDD as output 1.8V, for this reasoin I supply the uC with 3.6V on VDDH like this image:
this works fine...
Hello,
Although I already used the nrf52840 on previous projects (nrfxlib), I'm a newbie using nRF Connect and ZephyrOS (I previously used RTOS).
I'm integrating a driver...
I am trying to get provisioning by trusted user procedure of aws_iot working by making some changes in aws_iot nrf sample
I have tested it with permanent certificates and...
Hello Everyone,
For some time now I'm figuring out the best way to perform timer synchronization with µs-accuracy (+- 20 µ) between several BLE nodes in a star network with...
Hello ! I'm trying to adapt the code from the master-slave SPI example ( https://github.com/too1/ncs-spi-master-slave-example ) for my nRF54L15 development kit.
The master...