Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
To the kind attention of Nordic support team,
I have got in here two pictures of flash. The first one it is after installing bootloader and settings, softdevice and application...
Hi,
I am working on a product development that uses an nRF52832 (through a LAIRD BL-652 module).
We have a voltage point (named 5V), that is connected to SIO_28 GPIO through...
Dear,
I used ncs_v1.0.0_joakim to adapt the battery of my thingy91:
I used: battery_monitor_read(); to read the %battery, and it worked well
I just updated new...
I understand correctly that in order to use my private key for my applications, I must first sign an immutable bootloader with this key and upload it to the device?
I used...
Hello there,
It seems the CC310 backend for ChaChaPoly does not allow zero-length data or adata (associated data). I am implementing a protocol that requires this (Wireguard...
I am trying to change the default ATT_MTU size from 23 to 64.
my code uses Ble_nus service and Eddystone_Service.
Eddystone service is in connectable mode and it's where...
Env.: nRF52 customBoard, SES, nRF5_SDK_16.0.0_98a08e2
Hi,
I'am working with ble_app_template example and currently trying, to merge it with the experimental multiperipheral...
I have added an external SPI flash on the nRF9160 DK board, and wired it up to SPI3. I want to partition the flash into two ares for separate uses, but the partition_manager...
Hello.
I have just recived my nrf5340 PDK. I started with the hear rate example programming with the console. With some troubles but finally it worked.
Now I'm trying...
Hey nordic ,
I am doing project on BLE. I am Using Segger embedded studio v4.30b. (Board pca10040).
In that I am using features like advertising ,scanning and connect...
nrf52840 SoftDevice V6.1.0 release-notes written, The scanner and initiator roles can now be configured to receive ADV_EXT_IND PDUs on both 1M and Coded PHY, using a single...
Hi,
I'm using nrf52840 DK to connect and receive usbhid message with the message size > 64 bytes (examples 343 bytes), so the message is divided to multi packages. I modified...
I am trying to build the nrf9160 from segger studio. I have installed and expoerted path of zypher and gnuarm toolchain gcc-arm-none-eabi-8-2019-q3-update-linux
I am getting...
I'm trying to run SDK examples on BL652 module from Laird (which is basically nRF52832) by means of debugger from nRF52 Dev Kit
Strange thing is that all examples (even...
However, I don’t know which SDK we currently use:
“ The new device version is software compatible with the current version if using SDK14.2/15.0/15.2 and Softdevices...
