I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hey, When I initialize the device information service as follow ，It seems that It does not work ，RTT View show There cause a Fatal error 。 But if I initialize one of them...
Hi, I'm provisioning mesh nodes using nrf_mesh APP. After I finished it and added device into mesh network, I have some questions in configuration process.
In nrf_mesh APP...
When I send AT command, AT+COPS?, in example, +COPS: 0,2,"26201",7 will be returned. In this example, it returned one numeric string for MCC and MNC.
Can I simply read this...
Hi,
I don't find any information on the antenna used on the nRF51 DEVELOPMENT KIT. The chip is N51422.
I would like to have information like the gain of the antenna. Could...
Hi,
I'm Trying to add uart with DMA functionality to the asset tracker sample code.
but when running :
I get:
this is my nrf9160_pca10090ns.overlay :
these...
Hi Roshan
I want to use ViewModels in RecyclerView like I have to perform light on/ off (sendGenericOnOff(final boolean state, final Integer delay) android app)r each node...
Hi all,
I am running thethings.io examble of Thread SDK 3.1
I setup border router (Raspi 3B + NCP + ethernet) , Node (NRF52840DK)
In Node, I can ping to thethings.io...
Hello,
I'm currently a student and new to RTOS and modems in general, so please excuse my possibly very basic questions.
We have a running demo with an ESP32, where...
Hello everyone,
We are using the nrf52840 Dev Kit (PCA10056 1.1.0 2019.19 683465548)
SDK version: 15.3
OS: Fedora
We have our program working fine (RTT Logs OK...
I followed the install instructions from nRF Connect SDK documentation ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_ins_linux.html ), to build and...
I have nRF52832 board. I had interfaced nRF52832 board with STEVAL-IDP005V1 for FFT analysis. I am getting all the data and messages in STEVAL-IDP005V1 - UART (in PC). When...
Hi Team,
I working on the python script were i am trying to connect multiple nrf52 devices. nrf connect app for windows is connecting to multiple devices which is fine...
Hi,
We are designing a system using nrf52840, in which we intend to keep the wall clock time with battery support.
Reading about the internal RTC module, it gives an impression...
Hello,
I would like to use DMA on UART1 on the nRF9160. Can you provide an example for setting up the UART with DMA for Zephyr? I can't find any documentation or direction...
