My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
There is my function for writing to flash.
It works when NRF52832 start from reset, if works when the NRF52832 gets data over BLE but it does not works after "power down...
Hello, for some reason, the UUID's on a Galaxy Note 3 are messed up or are not being read properly. I have included screenshots of the issue. The note 3 is running android...
I'm trying to understand how the UARTs are configured on the nRF9160 DK.
The spec mentions that there are two UARTs, a primary and a secondary. https://infocenter.nordicsemi...
Hi Team,
I transplant the project nRF5_SDK_14.2.0_17b948a\examples\peripheral\uart to the project ble_central\ble_app_multilink_central, uart doesn't work.
It indicate...
Dear,
I am using LTE_M:
# LTE link control CONFIG_LTE_LINK_CONTROL=y CONFIG_LTE_AUTO_INIT_AND_CONNECT=n
and I want connect nRF91 DK with 2other systems (by UART)....
Im working with example: nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_uart
There is APP_ADV_DURATION parameter, it is maximum duration. How to get longer duration...
Hi Everyone,
We are building a product based on nrf52832 component.
We need to provide a firmware update functionality to the client/user so the end user will be able...
Hi!
We got the Zigbee examples running. Now we wanted to exchange the default keys.
Unfortunately we had to find out that this has no effect.
Changing the `ZB_DISTRIBUTED_GLOBAL_KEY...
Hi Everyone,
I'm using nrf52832(SOC) and LIS3DH accelerometer to get a motion detection.
I need simple code to get accelerometer data only using I2C communication.
Waiting...
I tried to reduced my hex file's size while converting to zip but it doesn't get size under 256KB due to which I am getting an error: Data size exceeds the limit.
Below...
Hey,
I don't get my application run on the nrf52840-dk board. Only if I choose "Build and Debug" I can run my software. Shouldn't the application start after I connect to...
I would like to receive data on UART asynchronously and handle the RX event in the backend in an IRQ handler. The application is - a user will be shown a menu and asked to...
Hi Sir,
If we would like to supply the external device through VDD = 1.8V when VDDH = 2.5V.
What is power efficient in nRF52840 when VDD = 1.8V when VDDH = 2.5V?
...
Hi!
We have been experimenting with the nRF9160's GPS using both one of our own custom board and the Development Kit v 0.8.5 (with similar results).
We run the gps sample...
Hi,
I am receiving the same error this guy was: " https://devzone.nordicsemi.com/f/nordic-q-a/28724/sdk-for-mesh-v1-0-0-with-ses-invalid-ascii-encoded-byte-line-1 " and...
