I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hi,
I'm using the NRF52840 with the "nRF5_SDK_for_Thread_and_Zigbee_2.0.0".
I tested the zigbee light_bulb example and zigbee light_bulb + ble. It works fine so my next...
I'm trying to extend the light_switch client example (from mesh SDK 3.1.0) to a gateway. The gateway will consists of nRF52832 and a WiFi module connected via serial interface...
As the title descripes i get an error with a file name in it but i can not locate this file.
I am working with the 802.15.4 wireless uart example on a nRF52840 DK. I only...
All nRF52832 based RF modules on the market have been certified using a Nordic SoftDevice. Some manufacturers say that it is ok to use a different Nordic SoftDevice without...
Hi I have been put into at task with a nrf52832 device (Mesh) that can only update the application. This is a big problem because we already have multiple device all over...
Hello. We are using nrf52840 for our product and I wanted to use aes ccm encryption for security. I was able to integrate CC310 library but I found out that encryption works...
i'm working on dynamic multiprotocol between ble and thread.
i want to ask about ble packet size in link layer and how could i change packet size ? is it could affect loss...
I am using arduino to send message through BLE to a mobile, which use "nRF Connect for Mobile" to scan the arduino.
I am able to get the information of Blood pressure (0x1810...
Hi,
We are developing a device with nRF52840 and mBed-os. We have a bootloader based on SDK 13.0.0.0-1 with softdevice s140 5.0.0-1-alpha.
Changes that has been made to...
Dear nordic,
I need a help from your side i want to create 1 hz(1000 ms time period) frequency pwm using PWM driver. i created upto 30 ms time period but i cant create time...
Hi, I'm using nrf52840 TWI master. Sometimes the I2C bus result as locked in endless loop to retry the start conditions. I see that in this case SDA and SCL are tied low for...
Updating the SoftDevice on the nRF52832 from S132 v2.0.x to S132 v3.0 using the Dual Bank Bootloader from SDK v11.0.0 results in the application not starting up after the...
I am planning to use Open bootloader example as my starting point for adding a bootloader to an application. I donot want Softdevice. Initially I am going to check the dfu...
i am working on ble_app_uart central and peripheral, so basically peripheral will sleep wake up and send advertisement packet to central . Now the issue is if peripheral is...
Hi, My Lord. When I run the example, I use short-name(BLE_ADVDATA_SHORT_NAME) advertising always "Fatal error",It's no use reducing payload.
On the other hand, how to add...
