Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
I'm working on a circuit based on nRF52810. Part of the design is an audio output that draws a high current, so the supply voltage of the NORDIC can drop to 2.8V for short...
hello there
i am using segger embedded studio with my nrf52 dk, i was trying a soft device example from the sdk 15, everything is working properly, but i see in seggar there...
Hi ,
I am using NINA-B301 EVK having nRF52480 core chipset. I am trying to flash all USB, UART examples to see the log or print on the putty prompt but I am not able to...
Hi,
I am working on a project which involves a number of low power nodes 4-16+ distributed over a relatively large area. There is one client which wants to retrieve data...
Hi. I am tinkering with BLE settings, and changed NRF_SDH_BLE_GAP_EVENT_LENGTH from 6 to 7.
I then get a 0x04 error code on this function after building and running the...
I am now based on nrf52832 SDK14.2 development, nrf52832 as a peripheral device, I want to connect with IOS phone, nrf52832 provides HID Service, but when connected with Android...
I am experiencing the following compiler error:
In file included from ../../../integration/nrfx/legacy/nrf_drv_uart.c:41:0: ../../../integration/nrfx/legacy/nrf_drv_uart...
I have some question about nRF52832 Bluetooth Firmware upgrade problem:
1. I have a device with nRF52832 in my hand. If I don't use the JTag interface, how can I confirm...
Hi,
We are using Nrf51 with SDK nRF5_SDK_12.3.0_d7731ad
We based a UART bridge on the BLE_APP_UART example
The UART connectivity is Rx/ x only (RX_PIN_NUMBER 0; TX_PIN_NUMBER...
Hi,
we've noticed that after performing an OTA DFU, the Bluetooth Address of the device changes as follows: new_address = old_address - 1
Example: Address before OTA DFU...
Hi there,
I am a beginner to the nRF series and I had the following question.
For a battery powered system, is it better to run the nRF52840 at a lower voltage such...
Hello,
i'm trying to program on 51422. The BLE signal,which runs well on 51DK, doesn't trigger any signal on my own PCB. i've successfully light the LED on my PCB. i think...
Hi,
I'm using nRF52832 and I'm trying to switch from SDK15.0 to SDK 15.2. While I've been able to install micro-ecc library in SDK15.0 and use OTA DFU, somehow I'm stuck...
Hello.
I want to integrate UART and SPI ,I am using SDK15.2. The problem here is i am not able to add app_uart.h to main.c(spi).
My question here is how to add it to main...
