Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
I am setting up the DFU example to compile in Clion using ARMGCC 4.9 2015q3 and cmake. Everything compiled as it should and the DFU advertises. However, when trying to do...
hello there,
i want to send and receive data using spi and i2c protocol and i am using nrf51422 .how to interface which pins should i use to make spi and i2c communication...
I have an application that toggles an LED on P0.26 based on a timer and that's working fine. Now I need to add a few more timers so I decided to use the APP_TIMER library...
I am having trouble with an application where the NRF52832 operates several devices as a TWI master. What is even stranger is that I have been working on this code for a while...
I am developing a keyboard using the nRF52832 and example code(ble_app_hids_keyboard).
SDK is SDK14.
Korean/English change is not possible.
The specification I refer...
hello there i have basic question about BLE. what is difference between link layer and GAP??
i know about host and controller. but in both layer there is advertisement and...
We are using the NRF52840 as a basis for BLE-based secure IoT network. I know that the Crypto library enables hardware-accelerated encryption/decryption. However, as far as...
Hi guys, I'm trying to nail down this TWI issue. PAN 89 is related to TWI being used in conjunction with the GPIOTE module. However I manually wrote my own application level...
Related to SDK 12.3.
Quoting this question :
GPIOTE PORT event generated on the
rising edge of DETECT signal. Please
have a look at section 15.1.2
2)DETECT...
Hello,
I am experimenting with sending large notifications from an nRF52 configured as BLE peripheral with SoftDevice S132 v5.0.0. I having some trouble receiving the notifications...
Hello guys,
I would like to execute code once a scan request from any other BLE device is received by the NRF52 using Zephyr.
Unfortunately, I am not able to receive...
Hi everybody,
I have an issue with my application, I want to use the ble with the same antenna that it use in the development board PCA10036,
Could you please tell me...
When I send 512 Byte from my Android phone I received only 20 Byte. How I can received more than 20 Byte? I used example project "ble_app_uart", SDK 14, SoftDdevice s132,...
I am working with SDK 14.0 . I see two "type" of advertising_init() function :
1-
static void advertising_init(void)
{
uint32_t err_code;
ble_advertising_init_t...
