Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Dear all，
i configure pin 3 to float input.when the pin3 input 0.3VDD--0.7VDD,the chip current have 25--400ua,other is normal(4ua) Why?
SDK:8.1.0
s110
#define PHOTO_PIN_NUMBER...
Hi,
I am using nrf pwm library from here: github.com/.../nrf51-pwm-library . I am driving two gpios for a piezo buzzer.
I call pwm_init(), then use the call set_frequency_and_duty_cycle...
Hi,
I am trying to run a MIDI slave chip with the nRF51822 which requires me to use the MIDI standard baud rate of 31250. Is it possible to use nrf_drv_uart with a custom...
Hi all,
i use the function sd_power_system_off() to put the micro in system off.
First question is about the the type of system off. There are different type of system OFF...
Hi Forum and Nordic Employess
I use sdk12.2
The Pstorage libraries are missing. I want a Pstorage (flash write / read) example along with the Soft Device.
Thank You
Hi all,
I see there are similar questions posted on this forum, but none answers my question satisfactorily.
What I have:
we use the nRF52 we use UART0 to
transmit...
I'm using SAADC on a NRF52832 DK to read a analog channel between 0-3.3V. I wanted to supply current with the board VDD but it's value is 2.8V and they're not event stable...
Hi
I'm trying to get higher throughput when connected as a central by increasing my Tx&Rx bandwidth to high (from the default medium).
uint32_t nrfErr; ble_opt_t opt...
Hello,
my custom board does not have external 32kHz crystal. I have managed to use NRF_CLOCK_LF_SRC_RC in SOFTDEVICE_HANDLER_INIT instead.
My questions are:
...
I have a Custom Board made by using nrf51822 soc but pc is unable to detect the board by using Jlink debugger.
Stlink was able to detect only when frequency selected as 20khz...
Hello dear Nordic Team,
I got a question regarding the device filtering options. I am interested in putting 10 chips next to each other. But every chip shall have only...
As I came to understand, all the services & characteristics are registered in a "GATT table" of some sort, so my question:
What are the functions used to create and...
I want to update the nordic device from another MCU with HCI DFU. I cannot figure out how to write the packet header.
In the Nordic documentation, it is writen to read the...
I want to add micro-ecc library for compiling bootloader secure code.
I tried as mentioned on infocenter.nordicsemi.com/index.jsp .
I am getting error as attached. I am...
