My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
As described in the docs.nordicsemi.com/.../powersave.html: “The application must choose the right duration based on the traffic pattern. Applications must also take appropriate...
Hi, I am using nrf9160 DK development board, i want to use gpio pins in this kit for a SPI interface from nrf52840, which pin i can use for this purpose. in datasheet it very...
Hello Nordic Team,
I am working on integrating the nRF21540 RF Front-End Module (FEM) with the nRF52840-QFAA in the 48-QFN package. Could you please provide the following...
Hi, I have reviewed the light_bulb app code in NCS2.8.0(include src code/CMakeLists.txt/prj.conf and so on)。 But I can't find where the path of matter is included, could you...
Hi all,
I wanted to enable read/write protection for MCUBOOT partition in my firmware from the application and encountered a strange problem. The build (build system - default...
Hi there,
This almost certainly has a simple answer but I can't work it out. I'm using the sample WIFI Scan for the above boards and can successfully scan away. But I'd...
Hi there, I am new to working with UART. I have managed to load the Nordic UART Service Client(Central) and UART Serial Port Emulation(Peripheral) without any sensors attached...
So, I am working on nrf52840 with nrf connect sdk and I want to get date and time in my project, I found a library in nrf connect sdk ->libraries->other libraries->date-time...
NCS 2.7.0 Zephyr 3.6.99
I have &uart1 described with status = "okay"
With a sub node of gnssdev: gnss-nmea-generic also with status = "okay"
I have tried with both pointing...
Hi, In one of the previous ticket (link: ), there is a link about an example to create an application with USB CDC/ACM and MSC at the same time. The link is no longer valid...
I am writing software for a battery-powered device that needs to go into the lowest power possible sleep mode when not in use and be able to wake up with one of 8 buttons...
Hello,
I've been trying to get the nRF Desktop Dongle/HID Forwarder to work, ie. I program a nrf52840DK as a HID forwarder, it connects to my bluetooth keyboard, and then...
Hey Team,
While connecting the battery to the nRF5340 Audio DK, we have observed that it only charges the batteries with 3 pin connector is being charged. However when we...
Hi, I just want to read accel and gyro data from the on-board BMI270 IMU on the Thingy 53. I'm using the sample code from zephyr and I've modified the dts and overlay file...
my chip is nrf52833. In guide document , the XC1 and XC2 would connect to capacity. Both pin is used.
My project need one pin TCXO. which pin I should connect to? XC1 or...
