My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
dear nordic team,
I was working on nrf52840 with nrf5sdk v 17.0.1 and sd v7.3 .Im using mergehex tool to combine bootloader+softdevice + App to download it to flash(using...
Hi Everyone.
IDE : Vs Code
SDK : nrfConnect SDK
I have tried to connect peripheral device based on address. User gives input , address of ble device and based on that...
Hi, I am trying to provision device using nRF mesh application. It discovers device and when i try to connect, it gives error device disconnected.
I tried this thing on...
Hi everyone, in special, Nordic; I'm facing a problem with the last two versions of the NRF CONNECT for Desktop (3.9.2/3) & the BitDefender Antivirus... I can download & install...
Hi everyone
I'm trying to generate the .hex file for examples like Tx and Rx or for my project but I'm not able to do that, please can anyone suggest me how can i do that...
I had been able to program my custom nRF52840 just fine until I wanted to change partitions. I erased everything and now am unable to communicate with the board at all. I...
https://github.com/NordicSemiconductor/pc-ble-driver-py/issues/210#issue-1089773469
I'm trying to build the project from sources. -using windows 10, python 3.8 -installed...
Port the radio_test sample to the Coprocessor sample to test the radio_test function error
How do I merge the two examples
I was hoping you could help me out
many...
Dear Sir.
We are using software based on mqtt simple project .
We added a 1 hz timer, Every 1 hz we toggle a led on and off.
Sometime the led is stuck on " on "...
Hi,
I'm trying to broadcast my BLE on my custom-made NRF51822 custom board.
My code was intended to run on Nrf51422, and it runs correctly on my PCA10028 DK with NRF514...
Hi,
we are working on nRF52832. my hardware is getting reset after a time. i don't know reset reason. my question is how to get cause of reset.
thank you
Hello,
I'm using the library LVGL on the board nRF9160 DK with an LCD screen.
In the lastest version of nRF Connect SDK (v.1.8.0), the version v7 is used for the library...
Hi,
The RAM Loading section for MCUboot states the following:
In case these drawbacks were acceptable, is it possible to run the image from external storage, without...
I'm trying to implement the full application for the nRF52832, while merging the Application, Mesh DFU Bootloader, SoftDevice and Device Page intelhexes into the one file...
Hi teams,
I noticed nRFConnect v3.9.0 is released.
After upgrading it, I got different errors as following, while detecting my nRF dongle & PPK during BLE app & Power...
