I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
I am going to find out an ideal throughput of NRF52832. And my environment is NRF52832/S332/MTU 247/connect interval 20ms.
Finally, i got a maximum value about 23Kb/s. I...
I have a nRF52840-PCA10059 dongle.
I have a PCA10040 dev boeard on which I programmed the ble_app_hrs_freertos_pca10040_s132 example after I modified HEART_RATE_MEAS_INTERVAL...
Hi,
I have some code which is based on the ble_app_gatts_c example sdk 15. I am using a Nordic NRF52840-dk pca10056 s140. Coding in Segger.
I want to each second change...
Hi,
I want to set the unused pins to low Level, however without using Software to do so, i.e. this has to be done before the chip is turned on.
How can I do that? Is...
Hello all, I have a little problem.
I`m trying to do an gateway communication using my NRF9160. The routine I`m trying to accomplish is next : -- Send message over serial...
Hi... i am getting the data through the RX,TX which is externally connected to the nRF52832 development kit , now i want to store the continous incoming data to the variable...
Hello, I am using nrf52840 board and SDK 16.0.0.
I am trying to merge this calendar example ( https://github.com/NordicPlayground/nrf5-calendar-example ) into ble_app_template...
1. I am trying to test the QSPI flash performance in nrf52840_DK ,but the QSPI init failed because of the event ready check,can i turn off the event check process?
2. I...
The recommended circuit in the v0.5 nRF5340 product spec differs a little from the nRF5340-PDK and I'm trying to understand the minimum requirements for an antenna. The spec...
Hi everyone, I am a beginner with the nRF52840 and I am looking at the example spi_pca10056 on SDK 16.0.0. What I've noticed is that at sdk_config.h file the pin configuration...
I have a question about what functionality is handled in the modem firmware vs. the application firmware.
I see from the nRF Connect SDK that the nRF9160 application communicates...
I'm using segger IDE for EVK-NINA-B1. I've downloaded nRF5_SDK_16.0.0 and trying yo run one of its example but getting error like stray '#' in program. I've attached 2 pictures...
Hi,
I'm using NRF52832 SDK15.2 to develop a smart band. Each time reconnect with iphone, the application assert in the peer manager event handler pm_evt_handler().
Any...
Hi Team,
I would like to know what does the system do after I call system off function as per below:
I have check through the oscilloscope to check how's the system...
