I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I am using simple ADC peripheral to read internal battery voltage(standalone). I am using two custom nRF51822 boards. One of the nRF51822 board is made by nRF51822...
Hello. I just started learn ble module and some confusing about ble_app_uart:
in file ble_nus.c we have function on_write this function calling when trigerred BLE_GATTS_EVT_WRITE...
I am developing a android app for firmware update on my device. I used buttonless dfu example to switch from application mode to bootloader mode, I write value 0x01 to the...
I'm trying to track down who is erasing and programming 0x800..0xFFF.
Does the SD_MBR_COMMAND_COPY_BL modify 0x800..0xFFF?
I inserted a CRC32 at the end of the MBR ...
How should we comprehend the nature of PPI, when dealing with radio interrupts?
For example, if I point radio event handler call back ( of this type:
static nrf_radio_signal_callback_return_param_t...
Hi!
I want to use UART function in my own project, base on ble_app_template.
but when I remove bsp module & board.h, add my custom pin config file, I can't see any UART...
Hi,
I'm attenting the tutorial to use Eclipse + gcc,
when I try to build the blinky project in Eclipse, I have the following error :
17:19:52 **** Build of configuration...
I am following this tutorial to be able to run the ble_connectovity example on the Nordic: github.com/.../pc-ble-driver
I can build and install Boost and cmake runs successfully...
ba_nRF51_spd.zip Hi,
I use nRF51422, SDK10, SD310 and fstorage fun beacuse I need save 10 uint32_t len datas to flash.
I did that....:
the callback fun
static void...
I have a proximity application where I would like to use the nRF51 DK (PCA10028) and Beacon (PCA20006) with Bluetooth Low Energy. I would like them to automatically link when...
Hi,
With the latest SDK (12) there isn't an UART bootloader example available. Am I right?
I'm trying to understand what are the options to program the nRF51 during...
Hello!
nRF52832 IC supports programming OTA the first time after its soldered onto a custom design?
We are designing a very small form factor wearable product and would...
Hello all,
I have a few questions about the best way to go about mass producing nRF51822-based devices.
Can anyone recommend a manufacturer that possesses the...
