I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
I am trying to bond the nrf51-DK with the android smartphone. I want to display the passkey to the user which would be done using BLE_GAP_IO_DISPLAY_ONLY. After which...
Hi, would there be any drawback in setting TIMER_PPI_CH_START to 11 to maximize the number of free PPI for application. 14->15 should be free to use in timeslot and ppis are...
hi, i am new to embedded system.
I am using SPI interface to collect data from the slave(imu) and transmitted it to nrf52 DK,previously,I just used RTT to show the received...
Hello,
I am truing to store data in the UICR register "customer area" from application code. The procedure is invoked only once when the registers are still empty. The...
Hello all,
In controlling two devices simultaneously from one central controller, I have noticed significant time delays in processing the second call to sd_ble_gattc_write...
Hi.
I am using PCA10028 board an SDK10.0.0.
nRF51's Max flash size is 256KB.
Q1. "s130_nrf51_1.0.0_softdevice.hex" size is 302KB already. How can we make HEX file less...
Hi.
I'm using PCA10028 and SDK10.0.0, S130 v1.0.0.
And "ble_app_hrs_c" example is my reference code.
It works well before i add code for timer as below.
void start_timer...
Hi I am an student who is a poor fledging embedded engineer.
I met an error on using nrfgo studio
when I click the tab [Device]-[nRF5X Programming]
I used JLink_V510p...
Hi,
Using ble-app-uart sdk9 example:
Is there a difference where I initialize uart in main? My code is able to run when I shifted the uart_init() after ble_stack_init...
Hi,
I am trying to figure out which GPIO pins i can use as UART on a nrf52 chip if i put it on a custom PCB (Not DK !!). From the reference manual (page 513, 48.10.7 and...
hi,
i want to restart my timer before it expires.
suppose my timeout is 2 second and i want to restart it in between 0-2 second based on signal when i receive before expires...
I've notice that the ST Balun NRF01D3 that I've used for my current design is not listed as compatible with Rev 3 (Build code: H) nRF51822 Silicon. Has there been any change...
Hi everyone,
I am looking into Crossworks and SEGGER's Embedded Studio and since they are related I am wondering which one of them is more recommendable? Right now Eclipse...