I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi there!
I would like to implement the nRF24L01-module to one project.
But, it would be great, too, if i can use the application manual to use only the chip itself with...
I have the nRF51-DK development kit (PCA 10028). I'm following the gcc tutorial here - devzone.nordicsemi.com/.../.
I'm using the ble_apps_hrs project as a basis for my...
Is it possible to connect DCC / DEC4 to a transistor to turn on / off a part in my circuit? I assume yes, but I just want to make sure.
Or, is there another way to turn...
Hi again,
If I use BluetoothGATTSetCharacteristicValue and set wr_auth = 1 in the ble characteristics, I receive a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event. I can also see...
Dear Nordic developers,
Does TWI supports bit level clock stretching? Means that after each bit (not byte) slave can hold down the clock and master should perform appropriate...
So I have the following bootloader code:
int main() {
uint32_t code;
sd_mbr_command_t mbr_command = { SD_MBR_COMMAND_INIT_SD, };
code = sd_mbr_command(&mbr_command...
My ANT BLE application runs on a custom board with a nRF51422, SD 310 rev 2.0.0
I can use the nRF UART app on an android phone, but on an iPhone with iOS 8.4 I can't even...
Hello,
I'm using an PTR5188 development board for my project which breaks out PIN 26 & 27 for ADC only. I'm using mbed as my development platform and haven't been able to...
Hi there
Can you clarify a point for me?
Quoting from Gazell link layer user guide:
"If only the ACK packet sent from the Host to the Device is lost, but both the initial...
Hello.
Reading the documentation of pstorage_load and the actual implementation has left me with confusion.
The documentation states that the size and offset parameters...
I uses S110 V6.00 softdeivce ,v5.20 SDK, and the nrf51822QFAC chip.
now I use the 32k ram ,but it is wrong.The program is not run.
I only use the 16k ram ,as same as nrf51822QFAA...
Hello everybody,
I'm trying to make TIMER1 working on nRF51822 together with softdevice.
In particular I would like to drive an interrupt line that goes to another microcontroller...
Let me ask you a communication sequence between nRF51822 and peripherals.We assume 5 peripherals.
In a sample program for multilink, original sequence is that 5 times repetition...
I'm trying to have an nrf51422 using S210 go to sleep and wait until it gets a signal from another ANT device to wake up. The other ANT device (master) will not always be...
