I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
i am working with nRF52840-DK and i want to implement a network with below futures
The node(means nRF52840-SOC) Should work as a listener
1. the listener should...
Hello,
I'm getting started with nRF Connect SDK. I've installed the toolchain and SEGGER through Getting Started App (because for some reason the Toolchain Manager froze...
Good day,
I have done DFU using the secure bootloader example in sdk16 using the nrf connect app. The DFU process completes successfully and the controller runs the new...
Good evening, I'm looking for a Blue Tooth BLE Low Energy for Low Power application.
This application should consume few mA only when the controller will be in TX and so...
Hi,
Could I get clarification on if the USB peripheral is isolated and won't backfeed?
In my product, VDDH & VDD are powered via a DC adapter that can be unplugged while...
Hello,
I continue to deal with Zigbee and I have another question. I use 2 nRF52840 chips. First nRF as a Zigbee Coordinator (CLI in SDK\examples\zigbee\experimental\cli...
Hi Team,
We are planning for use the NRF52832 Module for our development, In that for Secure data storage exchange we are implemented the some of the crypto mechanisms...
Hello,
When operating the Thingy91 in poor network connectivity environments, the call to getaddrinfo will sometimes block and eventually timeout returning a error code...
Hello,
I am using the nRF52840_DevKit and SDK-v16.0.0. I am planning to build and flash a bootloader with NRF_BL_DEBUG_PORT_DISABLE set to 1, which means APPROTECT and...
Hi,
I'm using SES v4.52b, a nRF52832 module (BL652) and nRF5 SDK 16.0.0. I'm trying to build a generic SPI Read and Write functions with the following:
The device I...
Hi there,
I am in the process of developing a custom PCB using the nRF52833 SoC. This board is quite simple, and doesn't use many of the pins of the nRF52833 SoC.
I am...
nRF5_SDK_16.0.0_98a08e2\examples\peripheral\uart. In the SDK 16 ,UART example,why the legacy driver nrf_drv_uart.c is used instead of the sdk recommended nrfx_uart.c.
Secondly...
hello,
I'm using SDK 16.0 with nrf52832, for storing some information iam using flash storage, during initialization, we are giving a starting and ending address to flash...
Hi friend,
We have a project with BLE connection. It sends out the Manchester data and the data modulates with 125KHz. Can we use PWM to do that? Will the data format be...
My platform is SDK16 with softdevice, MCU nRF52840. I used 2 pin to generate PWM at 125KHz for Manchester coding. I want them are at different pin polarity. For example, if...
