Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello everyone.
I don't know how to start the program when using Soft device.
In the case of example such as example / peripheral / blinky, if it is executed once from...
on the page
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16.0.0%2Flib_crypto_backend_micro_ecc.html&anchor=lib_crypto_backend_micro_ecc_install
step...
Hi,
I am working on low power mode with DK to apply optimization to our project.
And I verified DK with ble_uart_app can go down to less than 5uA in system on mode which...
I'm still trying more TCP stress testing similar to this inquiry . However, now I'm getting highly repeatable lockups on the node I am doing testing with.
Application code...
I was doing some stress testing of TCP connections and saw an oddity go by that has me scratching my head.
Here's the order of events as best as I can figure from correlating...
Hi,
I already achieved the update of all available nodes in a mesh network, where the update is injected over a serial connection to one node.
Now my question is, if I...
Hi
I'm confused by the concept of switching slots and sampling slots, or at least the way they are presented as being interleaved. For BLE, I believe that they are required...
I am considering using a high-Q BAW filter to drive as near the band edges as possible and roll-off noise beyond.
Source of my interest:
https://www.qorvo.com/design-hub...
I am using nrf52832 SDK14.2 development, now the system will generate some strange exceptions, I am worried about the stack overflow, is there any way to confirm whether the...
Hi All
We are using nRF9160DK and want to send data to the cloud (Adafruit or Thingspeak) using MQTT protocol but we do not have NB-IoT
Network in Our area so it's possible...
To the kind attention of Nordic support team,
I've been reading in this post:
https://devzone.nordicsemi.com/f/nordic-q-a/44042/using-nrf52810-with-gzll_nrf52_arm-lib...
Hello,
I need to validate my selection for crystals working with the NRF52840. For the 32.765kHz crystal I have chosen the 9HT12-32.768KBZC-T from TXC Corporation. For the...
i have test with RTC using nrf_calender.c.
It will prints output data on terminal window.
But, I didn't recognize the actual data.
Output data is mentioned below,
...
