I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hello,
I am a newbie to the Nordic development ecosystem. Just purchased a nRF52840-DK board and followed the instructions here:
https://infocenter.nordicsemi.com/index...
Hello,
Is there a way I can run JVM on nrf51 or nrf52 series devices? I have been searching the forums and did not find any updates on the same.
Any OS like embedded linux...
Hi,
We are currently in development of an IoT solution using the nRF9160. We are doing a set of EMC tests to ensure electromagnetic compatibility of the device. The test...
Hello,
I am trying to transfer a signal sampled on AN0 (P0.02) at 16kHz via Bluetooth using an ATT MTU of 247 and a 2MBPS PHY speed. The basis project used is examples ...
Hi, I am interested in using the NRF91 in our new products. So far I have modified the Asset_tracker example to send my custom data instead of sending the "sensor data". The...
Hi.
I have a question related to the Zigbee SDK's "On / Off Switch" example.
Studying the example, I cannot understand how to activate the "light_switch_send_on_off" function...
I'm trying to find out if the nRF52840 has the features needed for a new product. We need to be able to do the following from a Windows 7 or 10 program: scan for nearby BLE...
Hello,
I'm working on a project that makes use of both Bluetooth Service UUIDs like BAS and customer Service UUIDs. In the Bluetooth CCSv7 at Part A, Section 1.1, I found...
Hi,
our application is nearly finnished now, but I noticed, that after adding the secure_ble bootloader, the program enters the bootloader at poweron, then enters my application...
Hi, I got the schematic of thingy:92.
Now I have a question about netnabel: IF_SWD.
IF_SWD is connected to three nRF52840 GPIOs.
if the CTRL is high in IF_SWD, IF_SWD...
Hello,
I'm trying to use the USB MSC to show up as a file system, transfer the file into RAM, and send the file via BLE to an Android phone. This is with SDK 15.3 and S140...
Working with Fanstel BT840 module we have discovered that ADC channel VDD reads as zero or produces small mV level result. nRF52840 chip revision on these modules is QIAA...
Hello everyone,
i want to send a 16 Byte datapaket from a peripheral nRF52840 DK to my iPhone. (S140 SoftDevice) Im looking for an example who sends datapakets from peripheral...
