Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
I'm trying to build the "blinky" example found in nRF5_SDK_15.3.0_59ac345/examples/peripheral/blinky/pca10040e/blank/armgcc
Actually the pca10040e directory contains 'blank...
I am trying to port the 'radio test' example code in SDK15.3.0 from the nRF52832 to the nRF52810 so we can do some pre-certification testing of the radio in our custom design...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
To understand TWI better, I loaded 'twi_sensor' example as is on nRF52832...
Upon initial connection with iOS device, returned connection values at BLE_GAP_EVT_CONN_PARAM_UPDATE are:
ble_event: got BLE_GAP_EVT_CONNECTED. role: 1, conn_handle: 1,...
Hello,
I using the Segger with the last SDK. I modified the ble_app_uart example, I added the softdevice to the addition files. When I run the debugger everything seems...
Hey guys, Recently i decided to get the ICM-20948 DK and exploring it. I read all the info on their site and all their guides but the only briefly get over the topic, so i...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I was going to “Batter Service”. Battery level...
Hello, I am using the PCA10056 to program a nrf52811 chip on a custom board with SDK 15.3.0. I'm using the example ble_app_blinky_pca10056_s140 I am following the steps in...
I am working on transferring BMI160 sample given in zephyr samples (\ncs\zephyr\samples\sensor\bmi160) to nrf sample (\ncs\nrf\samples\nrf9160\bmi160).
Below is the changed...
I'm having a problem with the nRF52 SAADC. It's configured for
One shot operation on Channel 0 using pin Ain4.
Gain of 1/6
Tacq set to 40us
8 bit resolution...
HI,
I want to configure HT1632 LED driver using SPI communication protocol
for that i should send commands LSB to MSB
immediately data should go MSB to LSB
My question...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’ and “nRF Connect” app.
I am trying to understand...
Hi all
SDK 11.0.0 S132 version 2.0.1 nrf52832
I want to turn on the PWM and turn off the PWM after 1 minute. The device will do BLE advertising When the device wakeup...
Hi,
I have read a lot of posts about using the internal LDO/DCDC converters or using an external switch mode regulator, but haven't seen any answers I could use.
I have...
I am looking for guidance on how to fragment data in Extended advertisement on the nRF52840. I am using the "ble_app_rscs" example to advertise in non-scannable non-connectable...